How do you replace 1994 Lexus LS400 brake light bulbs?
email meet and I will send you a PDF showing and explaining exactly how. vbdenny.com I needed a direct anwswer so this is it now that I just finished replacing my 1993 LS400 brake light. 1. open trunk 2. gently pull back the carpet - like covering where the light is located and it will pull off and fold it back by weighting it down or having a friend hold it 3. look for two bolt head to the rear side which could attach the rear light and two other nuts that are all the same size which appear to be attachments to the rear light back portion (one may be hidden under a popped out piece of metal) 4. after removing these 2 nuts and bolts grab the screw sticking out at the top and pop out the top one by pushing back and the plastic surround over the rear light on the top of it should pull off gently and straight back 5. this opens up the light so you can gently wedge the top of the light with a flat head screw driver toward you and it will cause it to pop out so you can lift the entire rear light out 6. turn the bulb holders counter clockwise about a 1/4 turn to pull the bulb out 7. replace bulb by pushing down gently and turning it out 8. install new bulbs - do all three of the them just because this job is not worth doing again unless absolutely necessary 9. reverse your steps and if you don't have the snaps chew some bubble gum to hold it in place temporarily (just a joke but I might do it rather than going to buy a broken snap at the Lexus dealer) Say a prayer for those who follow in your path to unlock the secrets of how Lexus can make a good product and still force the average person to spend money just changing a light bulb - but then you aren't average if you accomplished this ... you're so thrifty and determined to crack the secret codes of the Lexus laws that you are now a member of the select group of owners who can and do change light bulbs ... Timothy for John (Please consider a donation to a charity instead of the Lexus dealer so I now this advice was worth giving to you and the world is not made up of car makers who immitate this kind of manufactured work) Amen....
How do you replace the headlight bulb on a 1997 Lexus LS400 and can I just replace the bulb or do I have to replace the whole thing?
Yes you can just replace the headlight bulbs. First you have to take out the cover by the battery. Then unscrew the cover by the radiator and simply lift it up to take it off. The light bulbs are visible at this time. Read More
1994 Lexus LS400 brake light bulb replacement: Purchase the correct replacement brake light bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement brake light bulb information. Then consult your owner's manual for the replacement procedure. As simple as it sounds, the owner's manual is the best place to start for brake light bulb replacement instructions and illustrations. You may want to consider replacing both left and right at the same… Read More
The center brake light bulbs can be replaced by lifting up on the rear light assembly and pulling towards the front of the car. www.lextechautomotivellc.com Read More
To replace the brake light bulbs on a VW Polo, pull away the carpeting in the trunk, unscrew the bolt holding the lights on, and disconnect the wiring. Replace the bulbs, put the wiring and bolts back, then replace the carpeting. Read More
no you do not Read More
you probally need to replace the bulbs Read More
if you open the trunk you will find a carpeted section on the lid and in the corner of the trunk where the lights are. You need to open the access doors to the light bulbs and replace the bulbs. the sensor will need to be reset by someone that can reset the codes Read More
email me and I will send you a pdf on how to change the body tailight bulbs. vbdenny Read More
There is a campaign on the brake bulbs for 2000-2003......If it hasn't been done you should get it done. The bulbs and sockets will be replaced. Read More
Changing any bulb on a Lexus is a challenge. The most difficult part is determining the exact process. The first time might take 2 hours while the second 20 minutes or less. While I have changed the headlight bulbs on my 90 LS400, I haven't on a ES300. My suggestion is to go to lexusownersclub.com and post a question in the ES300/330 forum. Someone there will know and help you as it is the best… Read More
How do you fix the stop lights of a 92 Lexus LS400 if the 2 attached to the body do not light up when you step on the brake but the two on the trunk are working and you replaced all the bulbs.?
Need more information. Do the tailight bulbs light up, just not the brake lights? What about the turn signals? If so you might have the incorrect bulbs installed. If the tailights, turn signal and brake lights are out you have something disconnected. There are three bulbs on each side of the body part of the car. The top and bottom bulbs are dual bulbs (1157) while the middle bulb has one filament. It is probably… Read More
the screws come off and you replace it Read More
Remove the tail light housing and replace the bulbs. Read More
Open the trunk....inside the trunk, on the back side are plastic covers that you can remove...there you will find your bulbs....find the brake light bulbs and remove them and replace them with new bulbs, then replace the covers. Don't forget about the 3rd brake light ...check it to see if new bulbs are needle. Also, if all of your brake lights aren't working...all at the same time...you might want to check your fuses. If replacing… Read More
What do you do if your tail lights do not work while driving though brake lights work fuses and bulbs are good?
on some cars the tail lights and brake lights are totally different bulbs gain access to the bulbs and have someone push the brakes so that you can determine which bulbs are the brake lights and replace the tail lights Read More
check light bulbs and fuses. light bulbs have 2 elements in them, one for stop and one for running. if thses are ok, replace brake light switch on brake pedal Read More
Fuse, brake switch, bulbs. Replace whatever the problem is. There is no way to know without being hands on. Bulbs most likely answer. Read More
To replace the brake light on a 2000 Pontiac Montana open the trunk to reveal the housing units. Find the lights and pull the bulbs out. Replace the units. Read More
You replace all the tail light blubs on your 94 Lexus es300 and when you step on the brake the dash light come on?
incorrect resistance of light bulbs installed. causes electrical feed back. replace all bulbs with factory replacement Also check that the tail light ground is ok. If the tail light bulbs aren;t grounded, it causes a backfeed of power to the dash lights and causes them to turn on. Read More
Answer The bulbs for the brake lights are usually separate from the normal tail light bulbs. Check and replace the brake bulbs first, and if they are still not working examine the fuses, switch and wiring. Read More
To replace the parking light bulbs, remove the screw on top of the headlight and pop out the clearance light. The parking light bulb will be accessible after this removal. Read More
The brake lights are located in the trunk of a 1997 Acura Integra. To replace them open the trunk and find the plastic housing. Remove and replace the bulbs. Read More
To change brake light bulbs on a 1998 Lexus ES300, open the trunk lid. Locate the plastic rivet on the side of the trunk liner. Turn the rivet while pushing in with a screwdriver. Remove the rivet and the trunk liner can be pulled away to access the bulb. Push in and turn the bulb to remove. Insert the new bulb the same way. Replace the rivet in the trunk liner. Read More
How do you replace the bulbs to dashboard lights for tach and speedometer in a 1995 Lexus GS300 They are normally red bars?
If you only need bulbs then your solution is easy, however if the needles themselves no longer illuminate, then there is no bulb to replace since the needles are the bulbs. Your local Lexus dealer will be happy to assist you in this matter, there is one catch...they will only sell you the entire instrument panel. The last quote I got was around $300.00. Read More
What if your 2003 silverado brake lights don't come on but the fuse is fine the bulbs are fine and the third brake light comes on?
replace the relay under the hood Also check brake lights switch had the same problem switched bulbs and worked fine Read More
Check the fuse, bulbs or there is a push button switch above the brake pedal that may need align or replace Read More
It sounds to me like your bulbs are out. These bulbs have a lifespan just like the light bulbs in the lamps that you have at home. These are easy and cheap to replace, and you can usually access the bulbs from your trunk, if you own a car. Read More
On a 1989 Acura Integra hatch back the brake lights are reached through the hatch itself. The brake lights housing are on the rear of the vehicle. Unplug the bulbs and replace them. Read More
You will need a Torx T15 driver and however many 921 bulbs you have burned out. There are 3 bulbs in the center high-mount brake light assembly. Remove the 3 Torx screws right on the face of the plastic bar and the assembly, with the 3 bulbs mounted, comes down. The bulbs pull straight out of their sockets. Push the new bulbs into the blade sockets. Put the assembly back in place and replace the… Read More
The lamp in the top brake light of a Toyota Highlander can be replaced by the locating the light housing from the trunk. Find the light cover and remove it to access the lights. Replace the bulbs. Read More
There are actually 3 bulbs (GE #1141). On my De Ville there is a small compartment on the rear dash directly in front (from inside the car) the high mount brake light. Simply open the compartment and pull back the trim exposing the 3 bulbs, replace any or all nonworking bulbs. Read More
Open the trunk, look under the high brake light location and the bulb should be visible then remove and replace. You may need to refer to your owner's manual on how to remove/replace those bulbs...I haven't had to replace any bulbs yet but it looks simple. (MW San Diego) Read More
The brake lights are accessed through the rear hatch. Find the panel on the rear sides of the car. Pop out the panel and access the brake lights. Replace the bulbs. Read More
The light assy has to be removed to take the bulbs out. Read More
Buy Sylvania Bulbs, 7443 type 12 volt Read More
Along the rear of the inside of the trunk there are four small bolts which need to be removed. Once removed, you will be able to push out the outer plastic cover holdind the light bulbs and wiring. From there, you can easily remove and replace the bulbs. Read More
To replace the rear brake lights on a Nissan Primera first open the trunk lid. Locate the tail lights and find the plastic cover which hide the bulbs. Remove the cover and then the bulb. Replace with a new bulb. Read More
Get in the back seat and grab the rear brake lite and pull the cover toward you. Bulbs are then remove able. Read More
Check the brake light switch located on the brake pedal lever. If there is power to the switch but nothing coming out replace it. Did you check the bulbs? Is there power to the rear sockets? Read More
Inside the trunk behind where the brake lights are are a plastic cover. Remove that and you will see one bolt. Reach in to the far side of the light and you will find the second bolt. Remove those and the brake lights can be pulled out. Now just twist the bulb holders and there are your brake light bulbs. Read More
http://www.sylvania.com/ go here and go to the auto sections put in you car make and model year, there it will show you what bulbs go where Read More
Remove the two screws holding the third brake light lens on then remove the lens, it may be stuck but it will pop off. Replace the two bulbs in there by pulling them straight out. Read More
To access the bulbs, you need to remove the fender well liner and the nut and disconnect the electrical connector. Read More
I have an 87 Aero Coupe and my 3rd brake light bulb is in my truck. I think yours would be the same too. Read More
Replace bulbs Check the fuse Check the stop light switch Read More
GET INTO THE TRUNK AND PULL DOWN THE CARPETING BY THE SIGNAL AND YOU WILL SEE THE BULBS JUST REMOVE AND REPLACE Read More
I assume you only need to change the bulbs. Go into the trunk and look up. You should see the wires leading to the mounting point for the third brake light, you candisconnect the connectors and then change the bulbs this way. Read More
You have to unbolt the entire tail lamp assembly to change the bulbs. Unbolt the tail lamps from inside the corners of the bed, replace the light bulbs, bolt the tail lamps back in place. Read More
you remove plastic red/white cover with 2 screws and remove bulbs. Read More
Replace the whole unit - it's got LED inside, not bulbs unfortunately Read More