answersLogoWhite

0


Best Answer

I know in my 1995 Accord my mechanic had to heat up the old bearing after removing 3 screws and then use a bearing puller to finally remove. The new ones then have to be pressed. I hope this helps tip: Timpkin Bearings are very good and most reasonably priced--I got both for less than $75

User Avatar

Wiki User

โˆ™ 2008-06-04 18:23:45
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How do you replace a bad wheel bearing on a 2001 accord?
Write your answer...
Submit
Related questions

How do you replace front wheel bearings on a 2001 Chevy Impala?

Remove the tire and wheel from your 2001 Chevy Impala. Remove the end of the axle. Remove the wheel bearing nut. Remove the wheel bearing seal and the wheel bearing. Reverse the process to install the new front wheel bearing.


How do you install front wheel bearings on a 2001 Ford Focus?

How do you replace front wheel bearing on a ford focus


How do you replace the right front wheel bearing of a 2001 Nissan Maxima?

The front wheel bearing on a 2001 Nissan Maxima is replaced by removing the wheel, prying off the bearing cover, and removing the retaining pin. The retaining nut can then be taken out, the calipers removed, and the rotor pulled to allow access to the bearing.


Is the 2001 Honda Accord front wheel drive rear wheel drive or four wheel drive?

The 2001 Honda Accord has front wheel drive.


What is the wheel base of the 2001 Honda Accord?

The 2001 Honda Accord has a 8 ft. 10.9 in. (106.9 in.) wheel base.


How do you find out which wheel bearing is bad on a 2001 Pontiac grand am gt?

how do you find out if wheel bearing is bad on a 2001 grand am gt


How do you replace wheel bearing assembly on 2001 Chevrolet Venture van?

Rear or front? rear


How do you replace wheel bearing assembly on 2001 Chev Venture van?

The wheel bearings are not really replaceable by themselves. This is because they are integrated into the hub assembly. So the answer is that you will have to replace the entire hub assembly to replace the bearings.


How to fix Mercury grand marquis 2001 wheel bearing?

Remove a wheel bearing on 2001grand marqus


Rear Wheel bearing repair on a 2001 Mazda Tribute?

The 2001 Mazda Tribute came equipped in a 2.0L L4 and 3.0L V6. The rear wheel bearing are sealed assemblies. These can be pressed in to complete the install. The OE replacement rear wheel bearings for this application are SKF #GRW266. It is recommended to replace the wheel bearings in pairs.


How do you replace a rear wheel bearing on a 2001 Mitsubishi spyder?

Remove axles and wheel with leverage bar. Remove caliber assembly. After removing the entire front mechanisms. Replace them with new, and reassemble tires.


How do you replace the radiator in a 2001 Honda Accord?

how toreplace radiator in a 2001 honda accord ex four cylinder


What is the 2001 ford explorer torque specs for front wheel bearing nut?

tourqe on 2001 front wheel bearings


How do you change a front wheel bearing on a Citroen Xsara SX HDI 2001?

how u do u remove a wheel bearing on a citroen xsara


How do you replace a front wheel bearing on a 2001 Ford Focus?

Focus is a front wheel drive vehicle. The wheel bearings are of the sealed variety.It's pressed into the hub. Take it to a machine shop to R and R.


Is the front wheel bearing in the hub assembly of a 2001 Honda V6 accord a separate unit or is it pressed in?

just replacd myself. it is pressed in. it will actually come out however it needs to be pressed back in.


Where is a Speed sensors located in a 2001 grand am?

The speed sensor is located inside the Wheel Bearing Assembly, and cannot be replaced separate from the Wheel Bearing Assy.


How do you clean the wheel speed sensors on a 2001 Chevy Impala?

the wheel speed sensor is all part of the wheel bearing hub assembly you cannot clean them you have to replace the hub assembly its not that hard of a job gm cars are known for this problem.


How do you replace a wheel bearing on a 2001 sentra?

hey, im going to be replacing a wheel bearing on a 2001 sentra. I'm doing it at home, and I was just wondering if I would be able to. Because I know that some bearings are pressed in with either a press or using a C-clap. so if anyone could help me out, it would really help me out. Thanks


How do you change the front bearings on a 2001 S10 4 wheel drive?

Remove the tire and wheel. Remove the axle end cap. Remove the wheel bearing seal. Remove the wheel bearing. Reverse the process to install the new wheel bearings.


How do you change the wheel bearings grand Cherokee?

how to change front wheel bearing 2001 jeep grand cherokee


Where is the abs sensor on the opel zafira 2001?

it is built in to the wheel hub and bearing


2001 Tracker diagram front wheel bearing?

We can't do diagrams, sorry.


Why is 2001 Accord making a low moaning sound from the left front wheel while driving but then stops when car slows down?

Worn out brake pads, sticking brake rotor, defective wheel bearing, or a problem with the tire. This could be dangerous so have it repaired.


Where is the oil filter in accord 2001 v6?

check on the inside of front passenger wheel.