answersLogoWhite

0


Best Answer
Copy

depends on which door your talking about but its located under the dash pad on the passenger side up against firewall and requires you to remove the entire dash and tilt it forward and down

2011-09-28 22:20:47
This answer is:
πŸ€“
🀯
πŸ€”
User Avatar

Add your answer:

Earn +5 pts
Q: How do you replace a blend door on a Chevy Express?
Write your answer...
Submit

Related Questions

How do you replace an electric blend door in a Chevy blazer?

Remove the dash assembly to gain access to the blend door actuator.


How do you replace blend door actuator on 97 ford expedition?

How do i replace blend door motor


Chevy blazer 1999 temperature blend door?

The blend door actuator can go bad. Big job to replace it. Dash assembly must be removed to gain access to it.


How do you replace blend door actuator motor on 1999 ranger?

how to replace a blend door actuator on a 1999 ford ranger


How do you replace a blend air door on a 2000 Pontiac Bonneville?

how do you replace a blend air door assembly on a 2000 pontiac bonneville


How do you replace the blend door on a 2002 mercury mountaineer?

If you do a Google search on Ford Explorer blend door there are lots of articles


How do you replace the outside door handle on a 1996 Chevy Tahoe?

How do you replace the outside door handle on a 1996 Chevy Tahoe?


How do you replace blend door actuator on 1997 Pontiac Bonneville?

locate blend door actuator for 1997 pontiac bonneville se


How many blend door actuator do a 2005 Chevrolet Silverado have-?

Most truck only have one blend door on it. This also goes for a 2005 Chevy.


Where is the Tahoe blend door actuator?

The blend door actuator on the late model Chevy Tahoe is located behind the dash in the glove box area. Broken blend doors and broken blend door actuators are a very common problem among Chevy Tahoe, Suburban, and Silverado models. Typically, to repair a broken blend door, a mechanic will disassemble the dash and replace the plenum box. It is an expensive and labor intensive repair. There are also some DIY solutions such as the heatertreater that provide hardware and instructions for performing the repair by removing the glove box rather than the entire dash. It is worth looking into if you think you have a broken blend door.


How difficult is it to replace the blend door on a 2007 Chevy Equinox?

You have to take the front dash apart almost to the firewall. A lot of 5,8and 10mm screws. Not a job for a DIY'er.


Where is the vacuum line for the heater blend door on a 2000 Chevy blazer s- 10?

The heater blend door is not run by vacuum. It is run by an electric actuator.


How do you replace air door actuator in gm sonoma 1998?

Where is the blend door actuator on a 1998 Sonoma


How do you replace the rear blend door actuator on a 2002 Ford Expedition?

You don't!


How to replace a blend door actuator on a 2001 S 10?

Get scissor doors.


How do you replace 1994 gmc sierra heater blend door actuator?

bs


How do you replace a 1998 cheyenne inside door handle?

how do I replace the inside door handle on a 1998 chevy cheyenne?


Where is the blend door located on a 2001 Chevy s10?

The temp blend door is located in the HVAC assembly behind the dash assembly. The dash assembly must be removed to gain access.


What is the purpose of the blend door actuator on a 1997 Chevy s10 truck?

The blend door blends the hot air with the cold air to produce the temperature you have selected on the temp control switch.


How do you repair Chevy Express 2000 rear van door latch?

left door latch is broke


How do i fix the blend door on a1996 explorer?

Probably a faulty blend door actuator. Remove the glove box to gain access to the actuator. Replace the actuator with a new one.


Why is the heat always going out on your Chevy Blazer?

The temp blend door actuator is probably at fault.


Where is the location hvac air blend door actuator on 2002 trailblazer?

where is the defrost/floor door actuator on 2002 chevy trailblazer


Replace 98 Ford Explorer heater blend door?

To replace a broken blend door, typically a mechanic will disassemble the entire dash, and replace the plenum box. Unfortunately this is an expensive fix because it is labor and parts intensive. There is a DIY solution called heatertreater. They provide instructions on how to access the blend door by removing the glove box, and replacing the blend door without removing the dash and plenum assembly. Broken blend doors are a common problem among Ford explorers, and most heating and A/C issues in late model Ford explorers are directly caused by a malfunctioning blend door.Read more: 2004_ford_explorer_heater_problems_clikcing_noise


How do replace the rear door handle on 97 Chevy astro van?

how do you get the door open