Auto Parts and Repairs
Headlights Tail and Brake Lights
Chevy Blazer
VW Golf

How do you replace a brake light bulb in a 1993 Mitsubishi 300 GT?

373839

Top Answer
User Avatar
Wiki User
2004-12-21 19:33:37
2004-12-21 19:33:37

dunno if there is a manual for a "300" GT but i know that there is one for 3000 GT's ;) refer to your car manual for procedures and correct bulb specifications. if you don't have the owner's manual around don't worry, it's easier than you think, just need common sense and safety in mind, otherwise, go to one of those auto parts stores and look for the repair manuals they sell. look for the one that contains the year and make of your car.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

check and see when your brake pedal is not pushed down if it is pushing the brake swith pin back in if so you need to replace the brake light swithch located behind the pedal

User Avatar

Defective or misadjusted, brake light switch.

User Avatar

Brake light switch defective or out of adjustment.

User Avatar

is it in the rear spoiler? Thru the trunk, light socket is right below rear window

User Avatar

Worn brake pads can cause the brake light to blink on the dash in a 1993 GMC Sierra 1500. This can also be caused by a faulty light.

User Avatar

The brake light switch is located above the brake pedal on a 1993 Nissan Sentra. To reach the switch the driver's door needs to be opened.

User Avatar

In order to replace the light, you need to open the trunk and pull back the panels to reveal the plastic wing nuts. Then, loosen the wing nuts and take out the whole lens. Then, replace the light bulb.

User Avatar

The brake lights and all of the rear lights can be access through the inside back molding in the rear. there are little knobs that you turn to access them.

User Avatar

The 1993 Ford Probe rear brake light lens cannot be removed. The tail light are a complete seal light. The light bulb's can be removed from the rear of the light assembly.

User Avatar

The brake lights may not work on a 1993 Honda Prelude if the brake light switch is no longer working. The brake light switch is in the steering column just above where the brake pedal is bolted to it. There is also a chance that a brake light fuse is blown.

User Avatar

The 1993 Toyota Camry backup light fuse is part of the brake light relay switch. The brake light relay switch can be found beneath the drivers side dashboard.

User Avatar

Pop the cover off by pulling at the corners away from the window, pull the tabs on the light shield, and replace the bulb with a 912 light bulb.

User Avatar

I know it will feel like you're going to break it, but if you firmly pull, it comes off. Replace bulb and snap it back on.

User Avatar

If you mean the brake light in your dashboard, it means that you have your emergency break on while the car is on.

User Avatar

The earth wire or metal track on the bulb carrier has gone. Its an easy repair and the carrier should just clip off the back of the light fitting.

User Avatar

See sources and related links below for 1993 Dodge Shadow tail light, brake light and turn signal light bulb part numbers.

User Avatar

there is a brake light fuse in the pannel you just need to look for it.

User Avatar

The switch is located just above the brake pedal.

User Avatar

1993 Toyota Camry brake light bulb replacement: Purchase the correct replacement brake light bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement brake light bulb information. Then consult your owner's manual for the replacement procedure. As simple as it sounds, the owner's manual is the best place to start for brake light bulb replacement instructions and illustrations. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).

User Avatar

u need brake fluid or ur braking brake down release it

User Avatar

This light is for brake on/problems with the brake. Check your brake fluid level and ensure it isn't dipping below the sensor on the master brake cyllinder. I had this happen to me during winter.

User Avatar

The 1993 Jeep grand Cherokee brake light switch simply plugs in and out. The brake light switch is located beneath the dashboard on the drivers side of the engine compartment.

User Avatar

In the control handle. If you take off the switch cover you will see the wires that lead into it. Usually it will need to be soldoered to replace it.

User Avatar

Lift the car on a jack, remove the tire, remove the brake shoe/caliper and remove the old brake pad. Put in the new brake pad, replace the brake shoe/caliper, replace the tire and lower the car to the ground.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.