answersLogoWhite

0


Best Answer

Open the Hatch door you will find two philipps screws next othe edge of the light after unscrewing these pull out the entire tail light this is on a ball hinge just pull stright out and change light.

User Avatar

Wiki User

โˆ™ 2006-04-02 18:32:08
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How do you replace a brake light on a 2002 Jeep Cherokee Laredo?
Write your answer...
Submit
Sign up for more answers

Registered users can ask questions, leave comments, and earn points for submitting new answers.

Already have an account? Log in

Related questions

You have 2004 Jeep Grand Cherokee Laredo brake and abs light is on how can you fix it?

How to change the brake switch on a 2004 Jeep grand Cherokee Laredo


Why does left side brake light go off when you step on the brake pedal on a 2000 grand Cherokee laredo?

Failed circuit board on the back of the light.


How are the brake lights on a 1999 Jeep Grand Cherokee Laredo interwired with the headlamps?

They aren't. The brake light circuit is not connected with the headlight circuit.


Why does the left brake light go out when you brake with your headlights on in a 2000 jeep grand Cherokee Laredo?

Replace the bulb. There are usually 2 filaments in each bulb and one is most likely out. Replacing it should solve the problem


How do you replace the brake light on a 2001 Jeep Cherokee?

To replace the brake light bulb you need to remove the whole light assembly. Once removed the change is simple.


My jeep Cherokee Laredo brake lights don't light up when I press the brakes?

Check the fuse, and the bulbs, then the switch on the top of the brake pedal


How do you reset the maintenance required light on a 1991 Jeep Cherokee Laredo?

Unplug or replace maint. timer


How do you replace a rear brake light on a 2002 Jeep Cherokee Laredo?

Open your tailgate and remove the bolts that hold the taillight on. I believe there is two of them. Carefully remove the light as the other end of the taillight is held in place by tabs. replace the light bulb/s and install by following in reverse.


Why won't brake lights on 1991 Jeep Cherokee Laredo work?

try unscrewing the back light covers and replacing the lights


How do you replace license plate light bulb on a 2000 Grand Cherokee Laredo?

Hard to see, but on my 96 Jeep Gr Cherokee there are two small screws next to each lamp on the outside.


How do you replace the shift console light for 1999 Jeep Grand Cherokee Laredo?

You can't. There's a circuit board connected to the shifter with LEDs on it. You have to replace the whole shifter. P/N # 52104149AC


How do you check engine light on 98 grand Cherokee Laredo?

With a scan tool.


How do you install passenger tail light kit for a 2004 Grand Cherokee Laredo?

How do you install passenger tail light kit for a 2004 grand cherokee?


What would cause the brake lites on a 2001 jeep grand Cherokee Laredo not to work the upper lite works?

I had the same problem, all I did was replace the fitting that the bulb goes in with a new one ( $8.00 fix) and replaced the tail light and haven't had a problem since.


Where is the brake pad rear light switch in 1999 Jeep Cherokee?

The brake light switch is behind the brake pedal.


How do you replace the Brake light on a 2000 ford explorer?

To replace the brake light on a 2000 Ford Explorer, remove the screws holding the brake light in place. Gently, but firmly, pull the brake light out of the vehicle and replace with a new one.


How do you fix 1995 Jeep Cherokee Laredo brake light?

To replace the brake light bulb you need to remove the whole light assembly. Once removed the change is simple.Best Regards,Jon M. It is best to avoid touching the bulb directly because some bulbs will somehow burn out if touched. Cleaning it with rubbing alcohol after handling it should make sure it is going to last a long time.


How do you replace brake light on Nissan tiida?

How to replace a brake light on a nissan Tiida hatch back.


Why head tail lights work and brake lights doesn't work on 2001 grand Cherokee Laredo?

Check the bulbs in case they have fused, next check the fuse, and finally it could be the brake light switch which may need replacing


How do you change the bulb on a brake light for a 2003 Grand Cherokee Laredo?

If Diamler hasen't messed that up too, the pre 1999 GC's have the bolts that hold the tail light on visible when tail hatch is lifted. If so, remove them, lift the light off, turn it over and there's the bulbs. Pop it out, replace it and put it back together. Good luck!


How do you fix the brake lights on a 1997 Jeep Cherokee?

Check the brake light switch located on the brake pedal lever. If there is power to the switch but nothing coming out replace it. Did you check the bulbs? Is there power to the rear sockets?


How do you replace the brake light on a 2003 Toyota Echo?

To replace your brake light, you need to unscrew the brake cover from the inside of the trunk. Then you will be able to pull the old bulb out and replace it.


How do you change brake light switch on 93 Jeep Grand Cherokee?

The 1993 Jeep grand Cherokee brake light switch simply plugs in and out. The brake light switch is located beneath the dashboard on the drivers side of the engine compartment.


How do you reset the maint required light on a 1992 jeep Cherokee Laredo?

A scan tool is required.


How do you replace the Brake Light Switch in a 2000 ZX2?

how to replace the brake light switch at the pedal of a 2001 ford zx2