answersLogoWhite
Auto Parts and Repairs
Geo Tracker
Chevy Blazer S-10
Late Model 1979-New Ford Mustangs

How do you replace a cylinder head on a 1994 Geo Tracker?

282930

Top Answer
User Avatar
Wiki User
2007-04-03 14:40:41
2007-04-03 14:40:41

I recommend you get a service manual; the one the dealer techs use not Chilton, etc.. Ebay usually have these for the specific year. If you are going to do any work on your car you will need the service manual. The head can be removed after you remove the intake and exhaust manifolds, valve cover,head bolts (the 16v engine requires some of the rocker arms be removed to get to the head bolts). The service manual will give a step by step procedure.

1

Related Questions

User Avatar

Buy a Chilton's repair manual. It has step buy step instructions.

User Avatar

remove head and replace gasket :)

User Avatar

You will need to remove the cylinder head from your 1994 Chevy. Remove the head gasket and clean the surface. Put the new head gasket on and put the cylinder head back to its original position.

User Avatar

Remove the intake and exhaust manifolds. Remove the head. Torque the head and manifolds to the correct torque and sequence, you will need a repair manual for this.

User Avatar

The 1994 Buick Century 4 cylinder head gasket will have to be removed and replaced. The head has to be removed, along with anything that is physically in the way of removal, before the head gasket can be removed.

User Avatar

Begin by removing the cylinder head from your Chevrolet S 10 four-cylinder engine. Remove the head gasket and clean the surface. Put the new head gasket on and return the cylinder head to its original position.

User Avatar

What is the torque for 1994 toyota starlet 1300 cc cylinder head

User Avatar

Remove the cylinder head and replace the gasket. -Possibly even have the head skimmed.

User Avatar

Bit of a tricky one ... It all depends on the condition of the cylinder head. If the cylinder head is warped then replacing the head gasket won't solve your problem. A warped cylinder head can be skimmed (if not too badly warped). If the cylinder head is badly warped then it would be much easier to replace the head than fit another engine.

User Avatar

A cylinder head isn't too hard to replace actually, just take off the hood and remove the smoke gasket and clean out the pipes, reach in and pull on the magic lever to open the Nether Portal, enter there and fight Satan to the death in a gory battle, succeed and God will take your cylinder head and replace it, simple!

User Avatar

If you are getting exhaust smoke coming out of the radiator overflow, you need to replace the head gasket that seals the cylinder from the cylinder cap where your coolant runs through to cool the engine.

User Avatar

It's up there. If you have seepage at the head gasket, you need to replace it.

User Avatar

You have to remove the cylinder head to access lifters.

User Avatar

You have to remove the cylinder head to access the lifters.

User Avatar

Yes they are tourqe to yield bolts and are one time use only. Im having the problem of locating new bolts right now for my g/f's 94 zoo.

User Avatar

There are five steps on how to replace the fuel injector in a cylinder. Some of the step-by-step instructions are disconnect the negative battery cable, relieve the fuel pressure, and remove the cylinder head cover.

User Avatar

Replace it , meaning the cracked head or the gasket . Neither can be repaired . The head can be repaired if its only warped from overheating by having it surfaced . It is best on the 8 valve or the 16 valve engines to replace with new parts.

User Avatar

replace the cylinder gasket and check for cracks and replace the head gaskets

User Avatar

Remove carburator then intake manifold then cylinder heads

User Avatar

It is on the back of the right cylinder head.


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.