Quantcast
answersLogoWhite
notificationBell

Top Answer
User Avatar
Wiki User
Answered 2013-05-23 00:03:24

To replace a drive cable on a Troy Bilt self propelled lawnmower, first make sure that the lawnmower is turned off. Then, locate the drive cable and remove it according to manufacturer instructions.

001
๐Ÿ™๐Ÿฟ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Still Have Questions?

Related Questions

How do you replace the drive belt on a toro model 20017 lawnmower?

Before working on the Toro model 20017 lawnmower, disconnect the spark plug. The drive belt is visible under the mover. Use a ratchet to remove the blade. The drive belt is now accessible and can be easily changed.



How do you replace the drive cable on a Craftsman snow blower?

having trouble replacing drive cable the end of the cable is an "s" and the pulley is in the way so it is too tight to fit in whats the proper method


How do you replace a drive belt on your Yardman 17HP 42 deck lawnmower?

remove the drive pulley, slip the belt on, then down through the frame onto the idlers that the pedal controls... done..


How do you replace the drive belt on a 42 inch cut Murray riding lawnmower?

In order to replace the drive belt on a 42 inch cut Murray riding lawn motor, first remove the blade after disconnecting the spark plug. The drive belt is now exposed for easy replacement.


How much will it cost to replace drive shaft cable for 2001 Chrysler 300m?

What is a driveshaft cable, your question does not sound lie you using the correct terminology



What is a floppy drive data cable?

a cable for connecting a floppy drive to the computer motherboard.


The function of hard drive cable?

To start, the hard drive cable connects your hard drive to your motherboard. Its really simple.


What is an eide cable?

The cable connects between the motherboard of the computer and the hard-drive or optical drive.



What is a vertical shaft engine?

Drive shaft is vertical- like a lawnmower. Cylinder is horizontal.


Which file system does a floppy drive cable have?

The cable? The cable has no file system, its just a cable.



How many connectors are found on a sata drive cable?

A SATA drive cable has two connectors. There is a single connector on each end of the cable.


How many pins does a floppy drive cable have?

AnswerA standard floppy drive cable in a computer has 34 pins.


How do you get a broken e brake cable on a 1997 Bonneville to stop chiming when you drive down the road?

Replace emergency brake cable Secure emergency brake pedal in its upper most position (released)


How do you replace speedometer cable on 1996 Geo Tracker 2 door 4wheel drive?

The 1996 Geo tracker speedometer cable is held in place by a retaining nut at each end of the cable. Loosen the retaining nuts. Remove the speedometer cable guide retainers. Reverse the process to install the new speedometer cable.


The function of ide cable?

An IDE cable connects a hard drive or CD drive to the main board of the computer.


What is an easy way to tell a current floppy drive ribbon cable from an EIDE cable?

The floppy drive cable would be about half the width than the other.


How many pins are there on a floppy drive cable?

There are two cables connected to the floppy drive; Power cable - 4 pins, Data cable - 34 pins.



How do you replace the alternator on a 1999 GMC Suburban?

Disconnect the positive battery cable, loosen the tension on the drive belt for the alternator, remove the electrical connections to the alt, remove the alt, and reverse the procedure. Tighten the drive belt tensioner to the required factory specs. Reconnect the battery cable.


My Renault clio automatic wont go into park and to select drive you have to pull back just before drive on the selecter what is wrong?

This is a common problem with the modern automatics ,they are mostly cable operated . Its a simple thing to adjust the cable referance Haynes manual. I have experienced this many times its rare but you may have to replace the cable. good luck & god bless.


How can you tell the difference between the hard drive data cable from the floppy drive data cable?

1. A floppy cable will almost always contain a small "twist" in it, in which a port of the wires are turned in reverse.2. A floppy cable has 34 pins. A PATA hard drive cable has 40 pins.


Still have questions?

Trending Questions
Do potatoes have genders? Asked By Wiki User
How many 20 go into 200? Asked By Wiki User
Unanswered Questions
Does arsenio hall have ms? Asked By Wiki User