answersLogoWhite

0


Top Answer
User Avatar
Wiki User
Answered 2008-10-27 19:49:40

Actually if you wanna grab a hammer and just beat the thing out it worked for me as well, but then i came onto another problem, my ball joint wont come out because its hitting the wheel bearing and i donr have enough money to get a shop to press the bearing out temporarily! Help!

The joint has to be pressed out in a hydraulic press. If you're a do it your selfer then remove the steering knuckle that it is attached to and take it to a machine shop and pay them to change it.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Loading...

Still have questions?

Related Questions

What is the torque specification for the lower ball joint on a 2001 Honda accord dx?

The 2001 Honda Accord lower ball joint torque specification is 90 pounds. The lower ball joint should be torqued in 45 pound intervals.


How do you replace the lower radiator hose in a 91 Honda Accord?

how do you put on the lower radiator hose on a 91 honda prelude?


Why would a Honda accord front end squeak when we go over every bump It has new struts and new bushings?

I have the same problem and the consensus is that it is the lower ball joints. Try to get grease into the lower ball joint (with a pointed applicator) or replace them.


How do you replace a 1991 Honda Accord LX thermostat?

Under the air intake (close to the throttle body) there is a joint that the lower water hose attached to the engine. Open it and remove the old thermostat and replace it with the new one. It should take about 10 minutes.


What is involved in changing the struts on a 2000 Honda accord?

Changing the struts on a 2000 Honda Accord requires removing the lower control arm, ball joint, and strut mounts. An alignment is suggested after installing new struts to provide the best drivability.


How do fix a squeaky front end suspension on the drive side of a 1994 Honda Accord?

The squeak is most likely coming from your upper or lower ball joints. Replace your worn ball joint(s) and that'll fix your problem.


How do you replace axles 1991 Honda Accord AT?

Support vehicle properly on jack stands. Remove both front wheels. Remove lower ball joint nut and cotter pin. Remove axle nut (36MM). Seperate lower ball joint carefully. Pull axle from housing and from transmission. Reassemble in reverse order. Torque Axle nut to 105 ft./lbs Install new cotter pin in lower ball joint after tightening nut. Torque wheels to 80 ft.lbs. Drive away a happy Honda owner.


How do you replace a front lower ball joint on an 86 Honda Accord DX?

ive been trying for the last 8 hours im gonna heat it up and drill it out tried everything else go to you tube and see Erick the car guy ...he shows how to do this.


How do i replace a Lower ball joint in 2001 Kia Rio?

You have to replace the lower control did assembly .


Where is the thermostat located on a 1997 Honda Accord?

follow the lower radiator hose


How do you replace the thermostat located on a 1992 Honda Accord?

follow lower hose to rear of engine. rember to bleed. bleeder located on the upper radiator hose housing.


Where is the thermostat located in a 1992 Honda accord ex?

The thermostat in a 1992 Honda Accord is found in the thermostat housing. The thermostat housing can be found by following the lower radiator hose.


Where are fuses to cigarette lighter on 1987 Honda Accord?

i have 98 Honda accord, has three fuse boxes. look on passenger side of dash.( lower) Also, one on the drivers side. (Lower) . These should be pull open panels


Does Honda Accord come in 4wheel or all wheel drive?

Well, I assume that a Honda accord has 4 wheels so i'd say both. But i think a standard accord in the lower price range comes with front wheel drive.


Is the 2000 Honda accord equiped with the LATCH latch lower anchors and tethers for children system?

The 2000 Accord does NOT have the LATCH anchors. It does have 3 tethers.


How do you replace the radio in 1987 Honda accord?

* Remove the ashtray and ashtray holder * Remove the mounting screws lower the radio unplug the electrical connector and antenna lead then pull the radio out of dashboard


How do you change lower ball joints Honda accord 1995?

On you tube.( Eric the car guy )show how to do this.


How do you replace lower ball joint ford 500?

with tools and a jack


How do you replace lower ball joint on 1996 Honda civic?

Not so easy.This is pressed into the lower control arm.So :Jack and support carRemove lower ball joint to upright nut.Separate ball joint from upright. Usually with a hammer and suspension fork.In some cases there is a spot weld that needs to be ground off in place of the snap ring.Remove the snap ring that retains the joint into the lower control arm.Use your portable ball joint and suspension press to remove and install the replacement joint.Assembly is reverse of disassembly.


How do you replace a lower ball joint on a bravada?

You will need to remove the tire and wheel from your Oldsmobile. Remove the retaining not on top of the ball joint. Pound the ball joint out. Reverse the process to install your new lower ball joint.


How do you change the lower ball joint on a 2001 Ford Ranger edge four wheel drive?

replace lower ball joint on ford ranger 2001


How to Change lower ball joints on a 96 dodre cirrus?

You can not just change the ball joint , you have to replace the whole lower control arm with ball joint.


How to open the hood of Honda Accord?

Hood release driver's side, lower part of dash or kick panel.


Where is the water pump located on a 1996 Honda Accord?

follow the lower radiator hose from the radiator to the water pump


Where is the ac compressor on a Honda Accord?

it will be on the front lower left side of engine below p/s pump.