the first thing you can do is take it to a mechanic which should do it for about $700.00. if you would like to do it your self you first have to take you engine out and put it on an engine stand. if you an Aussie then ring bursons or repco and order a head gasket kit. if you are from any other country then refer to your local car modification shop. after the engine is taken out undo the nuts and bolts etc. to reveal the head itself. one removed take old gasket off the head and place the new one (from the kit provided) where you took the original one from. once complete do the nuts and bolts etc up and make sure not to do them to tight because if you do you are looking at a bit of cash to get new ones and there is a risk of cracking the head. if that happens then your screwed. so do it all up and then put the engine back in. fix the brackets and there ya go :). good luck.
how do i remove the valve cover to change the gasket in a toyota camry 1996
When it leaks.
4 cylinder: half of hour of work (~$30-40) + the gasket (~$20-30).
how to replace valve cover gasket toyota rav4 2001
Remove the cover gasket, clean all oil around. Scrap off leftovers of the old gasket. Make sure there is no sand. Install a new gasket. Tighten it going across the cover from one bolt to another. Make sure that you do not tighten too much.
Yes! Check out the threads on the Toyota Nation forums, especially the ones about stripped head bolts.
replace the valve cover gasket, easy fix
Check to see it the valve cover bolts are torqued to specs. If this does not stop the leak, the gasket needs replacing.
Burning oil in a Toyota Camry can be caused by a manufacturer's defect in the engine's pistons. A worn out valve cover gasket can also cause burning oil.
Just reverse the way you took it off 'except' make sure there's no gasket material left on the seating surface and the gasket is in excellent condition on the valve cover. If you have any doubt replace the gasket. Cheers
To replace a light bulb in the map light on a 1996 Toyota Camry, the lens for the light has to be removed. There are clips at two opposite ends that have to be nudged gently with a flat screwdriver to get the lens cover off.
Take the inside cover off and there should be 3 bolts holding it on.
what is the torque specifications for a toyota camry 4-cylinder valve cover
The oil leak is coming from the valve cover gasket and leaking onto the exhaust manifold, the rubber valve cover gaskets get hard from the engine heat and start to leak, you will have to replace the rubber valve cover gaskets to stop the oil leak
Hi, I was looking for instructions as to "How to replace 1998 Toyota Camry rear bumper cover" and you got your question. If you have already replaced then please let me know otherwise I'm going to replace the part this weekened and I will let you know. Take care, Sam
The valve cover gasket, on a 2004 Jeep liberty, can be found by removing the valve cover. Peel the gasket off of the head and replace with a new gasket.
how do you replace the valve cover gasket on a 2002 mitubishi lancer
The vehicle year, model and engine info needed.
You have to check the valve cover gasket from all sides. If it's not the gasket then you should check the break fluid level, and the break tubes around the passenger tire.
What is a oil cover
how do i take the rocker cover off to change the gasketon a 2001 2.7 hilux petrol
The valve cover ask it, on a S 40 Volvo, can be replaced by first removing the valve cover. Remove the old gasket and replace with a new gasket.
remove the "dog bone" engine mount. then the 2 upper 10mm bolts on the timing belt cover. this will allow you to pull the harness out of the way to remove the cover.
3 hours labor and $50 parts. You can calculate the cost depending on the hourly labor rate in your area. Here in Northern California labor is ~$100 an hour!
That would depend on many things. The year of your Toyota Camry, engine size, and how you drive.