Alternators
Power Steering
Kia
Toyota MR2

How do you replace alternator belt 2000 kia sephiacant get the power steering off?

798081

Top Answer
User Avatar
Wiki User
2006-09-20 22:41:06
2006-09-20 22:41:06

I just recently had to replace mine. You have to loosen a few bolts. There are 2 at the bottom, one at top, and one on the side facing the front of car. The one on the side is to loosen and tighten the belt but you have to first loosen the first three I mentioned before. The one at top, you have to turn the powersteering pully to access this bolt. After that..just takes some good old fashion elbow grease. Hope this all helps.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Remove the power steering belt first then the alternator belt will go on.

User Avatar

Since There is no tensioner pulley you have to loosen your alternator.

User Avatar

BeltsYes, you must remove all of the belts to replace the alternator belt. The compressor belt first, then the power steering belt then the alternator belt.

User Avatar

Remove the plug on the bottom of the power steering fluid pump. Drain the power steering fluid out. Replace the plug to the bottom of the power steering pump. Replace the power steering fluid.

User Avatar

Refer to the instructions in the "Related Question" below regarding alternator replacement.

User Avatar

What have to do replace the belts water pump power steering

User Avatar

The alternator is the adjustment point. Loosen the bolts holding the alternator to the engine and slide the alternator in towards the engine. This will allow you to remove the fan belt. However, if you also have power steering, the power steering belt may have to be removed before the alternator belt can be completely removed. Loosen the bolts holding the power steering pump assembly to the engine and slide the pump towards the engine to remove both belts.

User Avatar

The power steering reservoir is underneath the alternator by the firewall.

User Avatar

Check that the alternator and the power steering don't work of the same belt.

User Avatar

what pulley/ there are only about 7 or so on a vehicle. water pump, alternator, ac, power steering pulley

User Avatar

For most cars there is a separate pulley groove and belt for the alternator and power steering. That way if your alternator belt breaks you could still steer the vehicle.

User Avatar

AnswerIts on the right hand side where the alternator is at. Look down, and you will notice a cap that says "POWER STEERING" on it.

User Avatar

How do you replace a power steering reservoir for a 2000 odlsmobile interigue?

User Avatar

How do you replace the power steering pump for a 1987 Toyota Supra?

User Avatar

how do you replace power steering hose on 99 chev venture

User Avatar

How to replace the power steering depends on which component you wish to replace. Let us know what it is and we will get back to you.

User Avatar

loosen the power steering pump pull that belt loosen the alt and remove belt and replace

User Avatar

first disconnect the negative battery terminal, remove the aux belt, unbolt the power steering pump(only the bolts not the lines ok) just move itout of the way so you could get to the alternator bolts, undo all the alternator bolts and wires and replace it.

User Avatar

The Power Steering Pump & Reservoir are below the Alternator, by the Firewall, on the Passenger's Side.....

User Avatar

how do i replace a power steering pump in a 1990 toyota camry?

User Avatar

power steering,a/c, and alternator

User Avatar

The power steering pump belt is located on the drivers side of the car. It runs parralell to the alternator / a/c belt, right above it. There is a pulley just above your alternator, the belt on this pulley is your power steering pump belt.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.