answersLogoWhite

0


Top Answer
User Avatar
Wiki User
Answered 2011-09-12 20:45:13

You'll need a Phillips screwdriver to take the lower steering collar off that's right under the cylinder.Once that's off, put the key in and look on the bottom side and look for a small button. Push it in and turn the key and pull the cylinder out.Good luck

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Loading...

Still have questions?

Related Questions

Replace ignition switch for 1993 Buick century?

Replace ignition switch for 1993 buick century?


How do you replace the ignition in a 1993 Chevy Lumina?

IGNITION ? ARE we talking ignition coil-ignition wires ignition switch-key & tumbler.


What is the firing order for a 1993 Ford Tempo GL 6 cylinder?

The firing order for the 1993 Tempo GL w/ 3.0l V6 is 1-4-2-5-3-6.


Are ignition switch and lock cylinder 2 different parts on 1993 Dodge Dakota?

Yes. The lock cylinder is metal part that the key goes into. The ignition switch houses the lock cylinder.


What is the firing order for a 1993 Ford Tempo GL 4 Cylinder?

1-3-4-2


Where is the Jeep Wrangler slave cylinder?

how to replace the slave cylinder on a 1993 jeep wrangler


How to replace ignition switch on 1993 buick regal?

I believe that the switch is located in the ignition cylinder (which you can get from any auto parts store). Unfortunately you'll need a steering wheel puller and a tilt removal mechanism before you can start with that.


How do you replace an ignition switch in a 1993 infinity J30?

change switch


How do you replace the ignition switch on a 1993 mercury topaz?

IF anyone has any imfo on how best to replace an ignition system on a 1993 Mercury topaz please call 714-6383162, or e-mail me at KN657@yahoo.com


How do you replace the fuel pump on a 1993 Ford Tempo?

located in the fuel tank probably have to remove for access


How do you know if the Ignition Switch has gone bad on a 1993 Dodge Shadow?

turn key inside the ignition and see whether the warning lights, ie check engine light and others dim as the key is being turned. If they don't dim then it is the ignition lock cylinder which is fairly easy to replace.


When is it recommended to replace a distributor cap and wire set for a 1993 Ford 4-cylinder?

75,000 miles


You have a 1993 ford tempo it turns over but when you release the key it stops and there is a buzz noise what is the problem?

Sounds like the ignition switch is bad


Where is the ignition module on a 1993 Ford Probe 4 cylinder?

In the dist. Takeit to Auto zone and have them check it out.


How do you replace the ignition switch on your 1993 Chevy K 2500?

Remove the retaining ring at the top of your 1993 Chevrolet K 2500 ignition switch. Slide the ignition switch out and remove the wiring harness. Reverse the process to install the new ignition switch.


How do you replace fuel pump for a 1993 Mercury Topaz?

I need to find out how to replace a fuel pump for a 1993 Mercury Topaz, 4 cylinder, fuel injection


Do you need to replace the whole ignition lock assembly when the electrical portion of the ignition switch goes bad in a 1993 Honda Civic LX Auto Trans?

If the lock cylinder is faulty, the entire steering column lock assembly will have to be replaced. reference " Haynes Repair Manual"


How do you remove the Ignition switch assembly on a 1993 Acura Legend?

you have to replace the whole steering column


Where is the fuel pump located on a 1993 Ford Tempo?

the fule pump is in the gas tank in the 1993 ford tempo


1993 ford tempo starter won't disengage new starter new starter solenoid new battery any ideas?

Try the ignition switch.or the ignition module located usually near distributer


What does the water pump on 1993 Ford Tempo look like?

it looks like a water pump that a 1993 ford tempo has.


How do you reset a fuel pump switch on a 1993 Ford Tempo?

how do you reset a fuel pump switch on a 1993 ford tempo


How do you remove and replace ignition switch on a 1993 Ford Ranger?

New AnswerUsing your current key, insert it into the ignition & turn the ignition to the "On" position but not the "Start" position. Do not start the truck. Next, using a very small screwdriver (preferably a Phillips head) insert it into the hole located under the ignition key cylinder on the steering column.Pressing upwards with the small screwdriver or nail, you will press in the release button.Firmly grip the key & ignition cylinder while pressing up on this release button & remove while in the "On" position.Insert your new ignition cylinder with the key in it, into the "On" position until it snaps in place. Going in, the release button does not need to be depressed.You now have a Cylinder key, that will not match your door lock keys!Best of luck.


How do you change the transmission fluid on a 1993 Ford Tempo?

Remove transmission oil pan for acces to filter Replace fluid, filter, and gasket


Can one easily replace a 22re with a 6 cylinder in a 1993 Toyota pick up?

i just replace the motor mounts with supra mounts