Depending on your model of car, and year.. (not given). You should have at least 3 screws holding your tailight cover in place. Sometimes the hatchbacks, you can change directly from trunk.. you will need to pull carpet forward to get at them.
Remove carpet inside trunk that covers tail ligh assembly, then unbolt tail light assembly, remove the assembly and bulb fixture of the bulb you want to replace, replace bulb and re-install in reverse order.
Open the hatch door and locate the two screws holding the tail light assembly and pull the assembly out of the housing. Unscrew the cover assembly, remove and replace the bulb. Reinsert assembly and replace screws
To replace a tail light bulb in a 1986 to 1989 Chevy Celebrity: 1. Inside the trunk next to the quarter panel there are 3 nuts that hold the rear header on. The middle bolt holds the tail light assembly on, take it off. 2. Pull the tail light assembly out enough for the stud to clear the body then pull to the side to pull the tabs out of the backup light assembly. 3. Give a slight twist to the proper socket to take it out of the tail light assembly and you can then replace the bulb.
Inside the trunk or hatch, remove the nuts(often 4)that are on the inside near your tail light. The whole tail light assembly can be pulled outward to change the bulb. The bulb assembly twists off. Replace bulb. Assemble in reverse order.
The tail light bulb on a 1999 Chevy Suburban is replaced by removing the retaining screws, pulling the bulb assembly away from the vehicle, and unscrewing the bulb. A new bulb can then be installed and the assembly screwed back in place.
Open the trunk. Pull back the carpeting directly behind the tail light that needs to be changed. Turn the bulb assembly to the left and it should come loose. Then replace the bulb and place the assembly back in and turning it the opposite way to lock it back into place. Replace carpeting.
For the Buick Skylark: You would go in through the trunk and remove the attaching hardware for the tail light assembly. After the tail light assembly is off, replace the bulb, and put the assembly back on. For the Volvo: you will either need to remove the outer casing to access the bulb OR go through the trunk and access the bulb through the package tray.
You will need to remove the tail light assembly to gain access to the bulbs. Open the tail gate and remove the two small screws that hold the tail light assembly in place, then wiggle the tail light assembly out in the open. Now you can unlock and twist the bulb socket out to replace the blown bulb.
you don't replace the tail light you just replace the bulb in it
The tail light is an assembly. The lens is not removable. To replace a bulb you remove the assembly by opening the liftgate, removing two fasteners, and pulling the light rearward.
to replace tail light bulb, u need to lower tailgate.on side of bed that is hidden when tailgate is closed you will find 2 screws. remove these screws and tail light assembly will come out of bed. the bulbs are the accesable from the rear of the assembly. replace bulb and then return assembly to bed and replace screws. shut tailgate
Lift the hatch. Remove the screws in the tail light assembly. Pull the tail light assembly out. It may need a gentle nudge. Now untwist the bulb assembly socket counter clockwise to remove. Replace bulb. Re assembly is in the reverse order.
There are two screws on the outside of the tail light assembly. Remove these two screws (keep them) and the assembly should be able to be removed from the truck. Carefully twist the socket out of the tail light assembly. Pull the old light bulb out of the socket and replace with new. Insert the tail light assembly into position in the truck bed and replace the two screws.
Remove two screws holding tail light assembly. Pull or Pry out tail light assembly. Locate center wire plug harness, turn to remove, pull out bulb, push new bulb in.
Remove the tail light assembly (as I recall, it attaches with a couple of screws and is clipped to the body). Remove the bulb holder, replace the bulb, reassemble.
Open the trunk and remove the nuts holding the assembly in place. With nuts removed the tail light assembly will come out the back then you can remove the light socket to replace the bulb.
drop the tailgate on side of bed where tailgate closes are couple of screws. thses hold the light assembly in bed. remove thse ,then remove light assembly light bulb is the able to be removed from back of assembly
In order to change a bulb in the tail light of a Chevy Celebrity you must remove the tail light assembly from the car. To remove the tail light assembly" 1. In the trunk next to the quarter panel there are nuts that hold the rear header on, the center nut holds the tail light assembly on. It will be in the center of the tail light assembly near the outer edge. Take the nut off and pull the tail light assembly out until the stud clears the body. 2. Pull the tail light assembly to the side to disengage the tabs from the backup light panel. 3. Twist the appropriate socket to remove it from the tail light assembly, then unplug the lamp and replace it. Reverse the steps to reinstall the tail light assembly.
sedan model: from the trunk pull out the carpet retaining screws/plugs to access the tail light assembly mounting screws. pull them out, pull the tail light assembly out. from here you can replace any needed bulb.
Open the trunk, locate and remove the defective bulb from the socket assembly in the tail light assembly. Replace the bulb with a new one, and lock into socket. Close trunk.
To remove the tail light assembly on a 1986 Celebrity: Inside the trunk next to the quarter panel there are studs with nuts on them that hold the rear header panel in place. Remove the center nut, which should be in the center of the taillight assembly. Then pull back on the lens so that the stud comes out of the body. Then pull sideways to pull the retainer tab out of the back up light assembly. Then you can twist out the socket that holds the bulb you need to replace. Replace the bulb and mount the tail light assembly back in place. Reverse these instructions to put the tail light assembly back in place.
On a 2012 toyota Highlander, How do you replace tail light Assembly
Open the tail gate, remove two small screws that hold the tail light assembly in place, wiggle the tail light assembly out, twist out socket and replace the bulb.
To replace the tail light bulbs in a 2000 Dakota open the tail gate. You will find two screws on each side that hold the tail light assembly in place. Unscrew these two screws then pull the assembly straight back. There are two pins holding the assembly so do not pull to the side they must come straight back.
Assuming it is the same as a '99 Galant: you go into the trunk and unscrew the three plastic caps that are holding the fabric-covered partition on on the side of the tail light that needs the new bulb. Then, undo the nuts holding the bolts on. There is a plastic-covered bolt there - push on that and it pushes the entire tail light assembly out. Then, undo the bulb holder and replace the bulb.