0
How do you replace front wheel hub bearing assembly on 2000 dodge durango?
Wiki User
∙ 12y ago
To my knowledge 1998-2004 are the same. Verify if you do or do not have front ABS The only part I will add: Make sure you use a high quality replacement part or you will be doing this again very soon.
Answer from a certified Chrysler technician:
http://en.allexperts.com/q/Dodge-Repair-809/1999-durango-wheel-hub.htm
Expert: Kevin
Date: 11/26/2007
Subject: 1999 durango wheel hub removal
Question
I am unable to remove the wheel hub assembly from the spindle. Front brakes are not ABS. I have been beating on the triangular flange, but it will not budge. The axle spindle moves freely inside the hub. All bolts, brakes, discs, ect. have been removed. This is a 4x4 SLT front drivers side. Do you have any suggestions ? Thanks,Ang
Answer - you have to put claw of a hammer in between the bearing and the spindle and hit it with another hammer and go around it in 2 spots and it will fall rite off its not pressed on. use plenty of dw-40 or something like it because its rusted on its very easy once u do it i have a 2001 i just did good luck
HUB/BEARING
REMOVAL
Raise and support vehicle.
Remove wheel and tire assembly.
Remove axle nut.
Remove ABS wheel speed sensor if equipped, Refer torakes.
Remove the brake caliper and rotor, Refer torakes.
Remove hub/bearing mounting bolts from the steering knuckle Hub/Bearing
Slid hub/bearing out of the steering knuckle and off the axle
INSTALLATION
Install the hub/bearing into the steering knuckle and tighten the bolts to 166 N·m (123 ft. lbs.)
Install the brake rotor and caliper.
Install ABS wheel speed sensor if equipped.
Install axle nut and tighten to 235 N·m (173 ft. lbs.) and install cotter pin.
Install wheel and tire assembly.
Remove support and lower vehicle.
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What is the part called that holds the entire front driver side wheel assembly on a 1999 dodge durango?
Hub and bearing assembly?
How do you replace front wheel bearing assembly on dodge stratus?
The front bearing for a Dodge Stratus is attached to the Hub. To replace it remove all the components on the hub assembly. There are three bolts that hold the assembly in place. Loosen the bolts and pry out the hub. Replace the unit.
How do you replace the tail light lens covers on a 2004 dodge durango?
The taillights are an assembly. The lens covers can not be replaced separately
How do you replace a wheel hub assembly bearing seal on a 1993 dodge shadow?
Front is easy, just replace hub rear is pressed in
How do you replace a wheel bearing in a 2000 Dodge Intrepid?
Remove the caliper.Remover the brake rotor.Tap the axle free from the rotor.Then unbolt the bearing assembly from the backside of the bracket.
What size are the hub bearing bolts on a 2003 dodge durango?
7/8
How do you replace front wheel hub bearing assembly on 2000 dodge Dakota quid cab?
how do i find out if i have ABS on my front wheel bearing , on my 2000 dodge Dakota quad cab 2 wheel drive
Who do you replace the water pump on a 2001 dodge durango?
either the bearing is noisy and driving you crazy or the pump is leaking ,or your truck is over heating and someone is guessing this will fix it
Heating cooling vacuum layout 2000 Dodge Durango?
How to replace the inside Spectra Heater Core on a 2000 dodge durango??
How do you replace a cv joint in a Dodge Durango?
take it to a mechanic!
How do you replace the front wheel bearing on a 2002 Dodge Durango?
to tell u the truth you are better off buying a new boot from a junk yard to put on then messing with the bearings
How do you replace the brake pads on a 2004 Dodge Durango limited with anti lock brakes?
Answering "How do you replace the brake pads on a 2004 Dodge Durango limited with anti lock brakes?"
