answersLogoWhite

0


Best Answer
Copy

try going to the parts store and buying a chilton manual for the make and model of your vehicle. It has diagrams and step by step instructions. It will cost somewhere around 30 dollars of so and if you ever need to fix any other part of the same vehicle you will have it at your fingertips.

I just did my left lower ball joint in my 97 F150. I got the Chiltons and the Haynes books. Haynes is much easier to follow. Hope that helps.

User Avatar

Wiki User

โˆ™ 2015-07-15 19:04:52
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you replace lower ball joint on a 1993 Ford F150?
Write your answer...
Submit

Related Questions

Replace ball joint on 2005 f150?

How do you get the lower ball joint out of the axcel hub assmb on a 2005 4x4 f150. the axcel appears to be in the way and the ball joint hits it when trying to remove. any help out there


How do I replace lower and upper ball joints on 1985 Ford F150?

you will probably need a ball joint press and a splitter


1993 Ford f150?

how to replace an oil pan that goes to a ford f150 1993? how much does the pan cost,and can you show a picture of it?


How do you replace the window regulator on a 1993 Ford F150?

What question


How do you change the tail lights on a 2003 Ford F150?

lower the tailgate, remove the 2 screws on the side when you lower the tailgate, pull assembly out and replace


How do I replace the Block Heater 1998 F150 4.6L?

How do I replace the block heater in my 1998 F150 4.6L?


Where is the OBD connection on 1993 Ford F150?

There is no OBDII connector on 1993 F150. Didn't start until 1996 (97 model).


How do you replace upper ball joints in a 2008 F-150 5.4L XLT Is this something a novice mechanic can do?

how do i change the ball joint on my 2008 f150


How do you replace lower ball joints on 1990 f150 4x4?

First remove the steering knuckle completely from the truck. Then remove any circlips (snap rings.) Then, use a ball joint press to push the old ball joints out and new ones in. Replace any circlips. Assemble the rest. Get the wheel alignment adjusted.


How do you replace a catalytic converter on a 1993 ford F150?

you cant, unless you have a oxy/acetylene torch take it to a muffler shop they're the pros


Where is the PCV valve on a 1993 Ford F150?

The PCV valve on a 1993 F150 is located in the top of the valve cover. it is a plug in type, and is easily replaceable.


Replace brake pads and rotors on a 2007 f150 super crew cab?

how to replace rea pads on 2007 crew cab f150


How do you change the battery on a 2001 Ford F150?

How do you remove and replace the battery on a 2001 Ford F150?


Is it dangerous to drive your ford f150 if the ball joint is separating?

Yes,


Does the 1993 ford f150 have fuel injection?

Yes.


Can you replace a rear main seal on an 1993 F150 with a 302 with out pulling the motor?

Yes but you must eather remove the transmittion or move it back enough to be able to work.


How do you replace the taillight on a 1997 Ford F150?

to replace tail light, you need to lower the tailgate> On the side of the bed that is covered by the closed tail gate are a couple of screws.Remove these screws and the tail light assembly can be removed.


How do you replace the alternator on a 1998 f150?

send it to a garage???????


How do you replace the rotors on a 91 f150 4x4?

Who cares


How do you change the brakes on a f150 truck?

go to following link you will get the answer: http://www.wonderhowto.com/how-to-replace-brakes-2003-f150/


How do you set timing on a 1993 f-150 5.0?

where is the spout connectoe on a 1993 f150 5.0?


How do you replace the brake light in a 2001 F150 with a bed liner?

lower the tail gate and look in tail gate jam. bolts are where the cables that hold tail gate are anchored


How do you replace the slave cylinder in a 1988 ford F150 6 cylinder fwd?

you just replace it


How do you replace the clutch on a 1990 F150?

i learned by watching the video


How do I replace a king pin 1993 Ford F150?

There are no king pins on these models.....if my memory serves correct they stopped using kingpins either in 79 or 80.....ball joints is what they switched to