answersLogoWhite

0


Best Answer

Those are pressure fitted with a special tool. Your better off bringing your truck to a automotive repair shop to have them done. I couldn't find the right tool to do the job anywhere.

User Avatar

Wiki User

โˆ™ 2015-07-15 21:17:11
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How do you replace lower ball joints on a 1997 Mercury Mountaineer?
Write your answer...
Submit
Related questions

Where do you recharge the AC on a Mercury Mountaineer?

There are two ports on the air conditioning compressor on the Mercury Mountaineer. The refrigerant to recharge the system is to be connected to the lower port.


How do you replace the fuel pump on a 1997 Mercury Mountaineer?

You lift the vehicle and lower the fuel tank. The fuel sending unit is removed from the top, and the pump can be wiggled out of the unit.


How do you replace the front lower ball joints on a 1995 Intrepid ES 33L V6 automatic?

You can't service the lower ball joints by themselves. You must replace the entire lower control arm.


How do you replace ball joints on 2004 2WD Ranger?

To replace ball joints on a 2004 2WD Ranger, lift the upper control arm of the spindle assembly and remove the nut holding the lower ball joint in place. Then lower the lower control arm to relieve the ball joints. Replace with new.Ê


How do you replace lower front ball joints 1996 jimmy?

To replace lower front ball joints in a 1996 Jimmy, raise the front of the car. Grease both ball joints and install the spindle. Next, place the spindle over the ball joints.


How do you replace the front brake pads on a 1999 Mercury Mountaineer?

Lift the car, remove the tire, remove the brake shoe/caliper, and remove the old brake pads. Put in the new brake pads, replace the brake shoe/caliper, replace the tire, and lower the car.


How do you replace ball joints on 1995 Nissan truck?

how to replace lower ball joints on 1995 4 wheel drive Nissan truck


Are the ball joints on the lower control arms on a 2000 ford explorer xls 4x2 replaceable or do you need to replace the whole lower control arm?

You can replace just the ball joints on the lower control arms , but the upper ball joints come with a new control arm


Show how to replace lower ball joints on 97 grand marquis?

If you need to replace the lower ball joints, check your owners manual for instructions. The manual should show you the location and how to complete the repair.


Where are the O2 sensors located in a 1998 Mercury Mountaineer?

On the exhaust pipe, lower, possibly near the catalytic converter.


Replace tierods and upper and lower ball joints in 96 gmc 4x4 seirra?

Change lower ball joints on a 96 gmC 4 by 4


Where is the computer module on 2003 mercury mountaineer?

The computer module in a 2003 Mercury Mountaineer is located behind the rear right panel in the truck space. The rear right seat belt panel must be removed and then the lower panel. The module is located beneath a green plug.


How do you replace lower ball joints on a 1998 Grand Marquis?

wear is it aat


How do you replace ball joints on a 1999 ford expedition?

which ones? upper or lower?


How to Replace ball joints on 2005 Malibu?

THE BALL JOINT IS PART OF THE LOWER CONTROL ARM


How do you replace lower ball joints on a 2000 S10 blazer?

first you take it in then pay them to do them for you!!!!!!!!!!


How do you fix lower ball joints on a 1997 Ford Mustang?

how do u replace the lower ball joint on a 1997 ford mustang


Can the balljoints on a 2000 mercury mountaineer be replaced?

I believe the lower balljoints can be changed , but the upper control arm assembly with the balljoint has to be changed


How do you replace lower control arm on a 1994 Acura Integra?

To replace the lower control arms on a 1994 Acura Integra safely raise and stabilize the car. Remove the lower ball joints and two bolts that hold the lower control arms to the car. Pull them off. Replace with a new unit.


Where is radiator drain plug on a 2000 Mercury Mountaineer?

There isn't one. Use the lower radiator hose- yes messy, I know, but the manufacurer doesn't care.


How do you remove lower ball joints on a vw beatle?

In the Standard Beetle the ball joints are pressed into the trailing arms. You need a special press tool to replace these. In the Super Beetle the ball joint is part of the lower control arm, you replace the arm when the ball joint is worn out.


Where is the radiator drain plug on a Mercury Mountaineer?

When facing the front of the Mercury Mountaineer, the drain plug is on the lower left of the radiator. Place a bucket under the drain plug spigot before loosening to catch the coolant. To empty the radiator, turn the drain plug three-quarters of a turn. Tighten the drain plug before re-filling with coolant.


How to replace 2000 Ford F-150 lower ball joints?

You need to have a "Ball joint press".


How do you replace lower ball joints in Hyundai Santa Fe?

Rather than replacing just the ball joints, replace the whole arm as replacing just the ball will more than likely not work. Use ball joint remover tools to remove and replace.


Where is the diagnostic plug 1998 mercury mountaineer?

The Data Link Connector should be in the lower part of the dash , below the steering wheel , between the inside hood release and the emergency / parking brake release ( it's behind a small removable plastic panel ) on a 1998 Mercury Mountaineer