Alternators
Mazda 323
Nissan Frontier
Rodeo Events

How do you replace the alternator on a 1997 Mazda 323?

303132

Top Answer
User Avatar
Wiki User
2007-08-29 09:04:42
2007-08-29 09:04:42

Disconnect negative of battery, disconnect/unplug wiring from alternator, remove adjuster bracket and bolts, loosen alternator through bolt and remove belt. Unbolt brake fluid master cylinder (2x 12mm head nuts) and remove from servo unit and push to one side. If brake pipes are tight you may need to disconnect these also (remembering to bleed brakes afterwards). You should now be able lift alternator off mount and carefully lift it out between servo and rear of engine. Refitting is in reverse order.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

This is from the Owners Handbook of my Mazda 323, 1996 : Alternator Drive Belt. 1. Loosen the alternator mounting bolt and adjusting bar bolt. Replace Fanbelt. 2. Turn the adjusting bolt until the correct tension is obtained. The deflexion should be 10mm. 3. Tighten bolts and recheck the tension.

User Avatar

To change the alternator belt on a Mazda 323, first remove the right hand air shield under the can. Then locate the pulley tensioner of the AC and loosen the bolts on the pulley. Finally, remove the alternator pivot bolt under the alternator to remove the old alternator belt and replace with a new one.

User Avatar

The Mazda Familia is also known as the Mazda 323. A 1997 Mazda Familia is recommended to use 10 W 30 oil.

User Avatar

The type of brake fluid a Mazda 323 made in 1997 uses is called Dot 3. This is the standard type of brake fluid for most modern cars.

User Avatar

its got 2 horns behind the front bumper.

User Avatar

Mazda 323 familia valve timing set up

User Avatar

how do remove the brake drum on a 1991 mazda 323

User Avatar

First, disconnect the battery and then, remove the alternator and power steering belt, then the timing belt cover, the timing belt and the two pulleys, unscrew the pump bolts and that's it

User Avatar

114x4 thats what i was told on my mazda 323 '84

User Avatar

The speaker size for a 1992 Mazda 323 would be 6-1/2.

User Avatar

i need carburetors Mazda 323 1.5L rebuilding Harold E. Lozano P. harenlo@cable.net.co

User Avatar

The Mazda 323 of that time from had a 1600cc engine but that isn't going to effect the issue of where to get a wiring diagram. Haynes makes a manual for the 1990-1994 Mazda 323. If you have a 1986-1989 Mazda 323, you will need to get a FSM (Factory Service Manual).

User Avatar

The recommended brand coolant for use in a Mazda 323 Astina is Genuine Mazda Long Life Coolant. This can be bought at any Mazda dealership.

User Avatar

Anonymoustwist off the plastic cover, pull the electrical plug off, unclip the metal clip by pushing the end where its clipped on and hinging it downwards, then pull the bulb out.

User Avatar

Usually it's inside the distributor, depending on the kind of ignition used.

User Avatar

4stud vs 4 stud, yes it will, 4 stud vs 5 studd, it will not. for all the 4 stud Mazda 323(f) from by 88 up to 2001 will fit

User Avatar

Where can I find the fuel pump relay on a 2000 mazda 323

User Avatar

can you tell me where the my 03 plate Mazda 323 2 litre diesels speed sensor is located as its not working .ta

User Avatar

Is it possible an electrical problem can cause my engine coil to burn on my Mazda 323

User Avatar

Slacken the nut at the top of the alternator (14mm I think) and the bolt at the bottom. Pull alternator out until you can only get 10mm of movement in the belt on the longest run. Tighten bolts. You will need the car up and take the shield underneath off to get access.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.