answersLogoWhite

0


Best Answer

1. Disconnect the negative battery cable.

2. Using a 3/8" drive, release tension on the tensioner and slip the belt off of an accessory.

3. Loosen the passenger side front wheel lug nuts, then raise front of vehicle and remove wheel.

4. Reinstall two adjacent lug nuts onto the brake rotor and using a prybar on the lugnuts and a socket with a breaker bar, loosen and remove the nut from the splined half shaft(this nut supposedly looses its torque ability and needs to be replaced after being loosened).

5. Remove the Stabilizer bar link. This will require two wrenches, one placed near the rubber seal area. (This step caused me a 3-day delay as I had to order a new one when the nut broke off with the bolt intake)

6. Remove the steering knuckle pinch bolt and separate the ball joint from the "A"-shaped suspension component with the appropriate tool or prybar.

7. Remove the "Y"-shaped exhaust pipe from underneath the vehicle. Spraying a lubricant on the 6 studs and nuts will aid the removal of these nuts. (Stripping of these threads is easily done with the galling that can happen from the hot conditions it has undergone. This accounts to adding another 3 days to my repair.If possible tighten the nut 1/8 of a turn before removing to keep from pulling rust into threads)

8. Remove the half shaft after extracting it from the steering nuckle. (It may be just as easy to remove the nuckle prior to removal of the half shaft, even though this requires removing the ABS sensor, brake caliper, and rotor.) A slide hammer can assist on freeing the half shaft from the other half shaft.

9. Loosen the 5 nuts needed to remove the half shaft that goes into the transmission. Apparently this half shaft is balanced from the factory and should be reinstalled in the same allignment, so mark the transaxle and the half shaft to make this possible. Remove the half shaft.

10. There are 3 electrical connections to the alternator: a 3-pin connector that can be removed by slipping off the clip, a 1-pin connector that is removed by gently prying the plastic clip portion up, and a battery cable sized cable that attaches with a nut that can be removed with a 3/16" socket.

11. There are now 4 bolts that need to be loosened before the alternator can be removed. Three of the bolts are easily reached, while the 4th is not visible and will have to be felt for. A 13mm socket will be needed to remove these bolts. The exhaust manifold and the attached O2 sensor blocks access to the hidden bolt, and removal of the manifold has its own set of hidden bolts which makes removal of the manifold to access the alternator bolt unfeasible.

12. Installation is the reverse of the above, but it is highly recommended that you replace the O2 sensor that is now exposed. It uses a square connector, not a round one like the more accessible "catalyst monitor" sensors. This vehicle has a whopping 4 sensors distributed over 2 banks. If you choose to replace this sensor, a tip on removing the electrical connector: find a 3-inch or so 3/16" diameter or less piece of metal(I used a tap) and using one hand to feel for the access hole which will point to the rear of the vehicle, use the other hand with the metal piece to insert into the hole and releasing the clip, pull on the connector to disconect the heated oxygen sensor. Alternative method This task can also be accomplished WITHOUT removing the drive shafts.

Jack the car up as high as possible and support with jack stands.

1. Disconnect the battery.

2. Remove the passenger side wheel & inner fender well covers

3. Remove the exhaust Y-pipe. Soak the seven nuts with penetrating lubricant.

4. Remove the serpentine belt from the alternator.

5. Unbolt the upper roll bar mounting point from the strut.

6. Unbolt the steering joint & press out of the steering arm.

At this point you should be able to see the bottom portion of the alternator.

7. From under the car you should see a bracket that supports the intemediate shaft. Unbolt the two nuts that connect the intermediate shaft bearing to the bracket.

8. Unbolt the three bolts that hold the bracket to the engine. Then remove the bracket. You now have enough room to get to the alternator bolts.

9. Use a 13mm socket with a universal joint on the end of a long extension to get to the upper alternator bolt. I was able to reach around into the wheel well with my right hand up to the top of the alternator bolt to help guide the socket onto the bolt.

10. The bottom bolt is easy to get to. But the universal makes it a little easier, because the Intermediate shaft is still there.

11. The rear alternator bracket is removed with a 10mm socket.

12. Once the bolts are out you make need to pry the alternator out of the bottom of its mount.

13. Once loose, pivot the alternator on its pulley down towards the control arm. If you are having problems bringing the alternator down past the rubber boot, just rotate the brake disk and it will walk the alternator out. You will have easy access to the electrical connections.

Replace with new alternator and reverse the process.

User Avatar

Wiki User

โˆ™ 2017-06-18 14:59:16
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How do you replace the alternator on a 1999 Mercury Cougar?
Write your answer...
Submit
Related questions

Will an alternator freeze up on 1999 Mercury Cougar?

If the bearings in the alternator get bad enough it can lock up.


Where is the alternator located on a 1999 mercury cougar?

if it is a 2.5 v6 than take the passenger front tire off and the alternator is right behind the plastic shroud


How do you remove the headliner on a 1999 Mercury Cougar?

how do you remove the headliner from a 1999 mercury cougar


Is a 1999 Mercury Cougar FRONT wheel drive?

Yes , the 1999 Mercury Cougar is FRONT wheel drive


Will a 2001 Mercury Cougar grill replacement fit on a 1999 Mercury Cougar?

No.


What to do if the odometer lights go out in a 1999 Mercury Cougar?

remove dash replace bulb(instrument cluster)


Where is the starter on 1999 Mercury Cougar?

It's a bit buried. Note that the 1999 Mercury Cougar has no user-servicable barts.


How do you replace the rear disk brakes pads on a 1999 Mercury Cougar?

Remove the tire and wheel from your 1999 Mercury Cougar. Remove the brake spring and the break caliper. The brake pads will come off. Reverse the process to install the new brake pads.


How do you remove alternator from 1999 V6 Mercury Cougar?

You have a shop do it unfortunately. new alternator from ford cost me in the area of $300 plus labor on top. you have to drop all kinds of stuff to get to the alternator. gotta take it out from underneath. goodluck.


What does relay R1 do on a 1999 cougar?

relay R1 is for the fuel pump on a 1999 Mercury Cougar


How do you replace alternator on 1999 Kia Sportage?

How do I replace the alternator on my 1999 Kia Sportage


Changing an alternator in a 1999 Mercury Cougar?

i dont know if you have changed this alternator or not but if you have and the new one quit call me i know the problem mine went out 5 times before i figured it out. 252-814-9267


What is the fuel capacity of a 1999 mercury cougar?

According to the 1999 Mercury Cougar Owner Guide : ( 58.5 litres / 15.4 U.S. gallons )


Where is obd port on 1999 Mercury Cougar?

The 1999 Mercury Cougar OBD 2 port is under driver side dash left of steering column


How do you replace the rear speaker on a 99 Mercury Cougar?

Remove the rear speaker cover from your 1999 Mercury Cougar speaker. Remove the rear speaker retaining screws. Remove the wiring harness from the back of the speaker. Reverse the process to install the new speaker.


How do you replace the water pump on a 1999 Mercury Cougar?

Take off old water pump and put on new very easy.


1999 Mercury Cougar engine diagram?

The engine diagram for a 1999 Mercury Cougar is used in diagnosing and repairing problems. It gives the location of each component and its connection type.


Where can you buy 1999 Mercury Cougar headlights?

Ebay, http://www.nextag.com/mercury-cougar-headlights/search-html, or just drive to your ford/mercury dealer.


What are the signs of bad voltage regulator on 1999 cougar?

It is built into your alternator


How can i fix a 1999 Mercury Cougar door lock?

The door lock, on your 1999 Mercury cougar, can be replaced by removing the inside door panel. The locking mechanism is easily visible and can be changed.


What does the gas cap light look like on a 1999 Mercury Cougar?

I was looking at the 1999 Mercury Cougar Owner Guide and it does not show that it has a gas cap warning light


Where is the CD player in a 1999 mercury cougar?

According to the 1999 Mercury Cougar Owner Guide the six disc CD changer ( if equipped ) is located in the luggage compartment


Where is the obd2 plug on 1999 cougar?

The 1999 Mercury Cougar OBD 2 port is under driver side dash left of steering column


How do you change the fan switch on 1999 Mercury Cougar?

Why are you replacing the switch? If the fan works only on high speed, replace the fan resistor. There was a TSB for this.


How do you remove the door panel on a 1999 Cougar?

how to remove the door panel on a 1992 mercury cougar