The antenna mast screws into the antenna mount on the fender. Unscrew the old one and crew in the new one. If you need to replace the entire antenna mount, you will need a new antenna mount assembly with antenna cable.
The antenna screws into the mount on the roof
The antenna mast screws into the antenna mount on the fender. Unscrew the old one and crew in the new one. If you need to replace the entire antenna mount, you will need a new antenna mount assembly with antenna cable. Unscrew the antenna and then unscrew the antenna mount nut. Unfasten the mud guard in the wheel well enough to pull it aside and reach up to the antennae. Remove the kick panel to find where the cable enters the jeep.
go to your dad for help he would like that
what are the torque specs on body mount bolts
You can replace your 1995 Chevy Corsica motor mount by loosening the motor mount retaining bolt. Jack the engine up approximately 3 inches. Remove the motor mount retaining bolt and the motor mount bushing. Put the new motor mount bushing in and reverse the process.
Whats the easiest way to get broken cab mount bolts out on a 1994 chevy 1500 extended cab
You can get the spare tire off a 94 Chevy Silverado truck by reached under the rear bumper and turning the release knob. It will slowly lower the tire down until it can safely be removed from the mount.
Installing a CB radio in a Chevy Impala begins which installing the mount and location a suitable power source. The radio is then mounted to the dash, wired up, and the antenna connected.
Yes. You may need to make other changes, such as different flexplate, different driveshaft, or possibly different transmission mount. But it will work.
It is as simple as removong 2 bolts and replacing the mount. Goodluck, JOe
The antenna is in the rear window, and it's almost worthless! I'm looking for a way to mount an exterior antenna.
To replace a motor mount on a 1995 Chevy S-10 4-cylinder 2.2L, the engine will need to be hoisted up out of the vehicle until the new motor mount is welded in, if the mount is rusted out. Then lower the engine, keeping it on the hoist until both motor mounts are secured. Then, it will be necessary to hook up all other parts to the motor, like the transmission. If the motor mount is only missing the bolt, then replace the bolt with a new one.
Start of Chevy Astro cable replacement.I have a 2001 Chevy astro and have been able to lift up the grill on the side of the antenna using a star screwdriver. Underneath the grill the antenna mount removes with a socket wrench. On the end of the radio I have found that the part of the dashboard over the radio just pops off and then there are just a couple clips you push in on each side of the radio that let you slide the radio out. The antenna connection on the back of the radio is just a simple coaxial plug that pulls out. However, now my problem is that somewhere behind the dashboard the cable seems to be tied down to something and I cannot pull it out either end. My next attempt will be to try pushing something like a piece of wire down the hole from the antenna mount to see if I can get it to come out somewhere inside the van where I can grab it.
if it is an LED unit you cant you have to change the assembly as a unit
No it will not.
Remove the wiring harness from the high mount brake light. Remove the retaining screws. Reverse the process to install the new high mount brake light.
The Generation X antenna booster should be mounted on your phone.
I would first check the u-joints in the driveshaft. But it sounds like the transmission rear mount is broken. CHECK TRANSMISSION MOUNT.
You don't "fix" a motor mount, You replace them. You may be able to use a bottle jack to lift the side enough to remove and replace the mount. Good Luck and Remember.Change Your Mind, Not Your Oil.Use the First In Synthetic Motor Oil's.See My Bio For more information.
Remove the old mount & replace with the new.
http://fastpartsnetwork.com/ Fast and reasonable
If it is where the filter meets up to the mount there actually is a gasket there. If it past the mount you may need to replace the filter housing.
To replace the dome light gently squeeze the lens to release the clips and remove. Next release the bulb from its mount. Install the new bulb and replace the lens.
where its located the oil gage in a 2000 Chevy tracker mortor 2.0