Heater Cores and Blower Fans
Infiniti G20
Grand Am GT
Grand Am SE

How do you replace the blower motor resistor on a 1993 Infiniti G20?

444546

Top Answer
User Avatar
Wiki User
2008-06-14 15:29:32
2008-06-14 15:29:32

Pictures and description http://www.cardomain.com/ride/299921/2

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

The blower motor resistor, for your infinity automobile, can be found in the engine compartment on the firewall. The resistor will be on the passenger side of the firewall.

User Avatar

The blower motor speed resistor is burned out. You can replace only the resistor but the resistor probably burned out because the blower motor is going bad. If you want to fix it for good, replace both the blower motor and blower motor speed resistor.

User Avatar

Check to see if you are getting power to blower motor - if so replace blower motor If not check fuse, switch, resistor pack.

User Avatar

Check to see if you have 12 volts at the blower motor. If yes then the blower motor is bad. If no, then the resistor, relay, or fuse is bad.

User Avatar

Take the glove box out then behind it if you listen you can find the blower mtr not all the facts but its how far I got

User Avatar

To replace a blower motor on the resistor first you take off the nozzle and then you go into the motor through the nozzle and unlock it then repeat and oil and done.

User Avatar

# Locate the blower resistor under the right-side of the instrument panel # Disconnect the electrical connector from the blower motor resistor # Remove the blower motor resistor mounting screws and remove the resistor from the housing # Installation is the reverse of removal

User Avatar

A malfunctioning blower motor resistor will cause the blower motor not to work. When the resistor is bad the blower motors will not turn on.

User Avatar

To test the blower motor resistor, unplug the resistor connector. Each blower motor switch input terminal on the resistor must have continuity to the resistor output terminal, which is connected to the circuit going to the blower motor. If the blower motor resistor continuity does not check OK, replace the faulty resistor.You need a multimeter to test the resistor block and there should be continuity between all terminals.

User Avatar

you need a new blower motor resistor with auto temp control

User Avatar

To change the blower motor resistor in a 2002 Nissan Maxima, locate the blower motor resistor under the glove compartment on the passenger side of the vehicle. There is a clip that is depressed and then the resistor will slide out. Remove both ends of the resistor and then replace with the new resistor.

User Avatar

One can replace blower motor resistor on 2003 Nissan altima by removing the old using spanners and replacing it with a new one.

User Avatar

where is the location for a blower motor relay on a 2006 ford freestar

User Avatar

it needs a blower motor resistor to make the fan settings work.If you replace the Blower MOTOR Resistor it should resolve the problem.

User Avatar

the blower motor resistor is located behind the blower motor which is located behind the glove box there is clip wires you need to disconnect and then connect the new one.

User Avatar

The a/c heater blower motor resister is located in the vehicle on the passengers side inside the housing next to the blower motor...............Remove the blower motor resistor wire harness connector.Remove the blower motor resistor screws.Remove the blower motor resistor.

User Avatar

You must remove the glove compartment door to access the blower motor. On top of the blower motor will be wires connecting to the top. Release the connecter and let it dangle. Then using a screwdriver, remove the blower resistor on top, where the wires connected, and replace with a new resistor.

User Avatar

Generally the blower motor resistor is found close to the blower motor. It relies on the blower motor to keep it cool.

User Avatar

Fig 15 Blower Motor ResistorNOTE: The blower motor resistor is located on the lower right side of the heater housing.REMOVAL# Remove lower right underpanel silencer/duct. # Disconnect wiring connectors on blower motor resistor. # Remove blower motor resistor retaining screws. # Pull blower motor resistor out of heater housing.

User Avatar

The fuse. The blower motor speed resistor. The blower motor relay. The blower motor switch. Check for power at the blower motor connection.

User Avatar

this resistor is located next to the blower motor in the heater plenum. the coils sit in the air stream. remove the connector and the fasteners and pull the resistor block out.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.