There are two rear facing tabs on either side of the rear cover housing. Using a thin blade type device, gently pry up while pulling slightly to the rear. Do this one side at a time, and the cover will slide off to the front of the car or toward you. Don't pry the tabs out very far maybe a 1\16 to 1\8th of and inch, else you will brake them. Also don't pull the housing out very far until you get the second tab disengaged
Remove the tail light housing and replace the bulbs.
There should be a few screws around the housing of the brake light/indicator housing then it is as simple as taking the bulb out and replacing it with the appropriate one.
To replace the brake light first you need to remove the lens housing from the car. Next pull the entire bulb assembly, or housing, out of its hole. Remove the bad bulb, replace with the good bulb and place lens housing back into position. Secure the housing with the screws.
To replace the brake light on a 2000 Pontiac Montana open the trunk to reveal the housing units. Find the lights and pull the bulbs out. Replace the units.
If you're asking about the ones at the corner, the whole housing comes out to get to the bulbs. Just pull back the carpet lining, and you should see a few nuts that hold the housing in place. If you're referring to the high mounted brake light in the rear window, that should be accessible from the trunk.
In the top of the trunk near where the brake light is located, there is a small plastic window, remove it and you access the light bulb.
How do you replace rear window brake light bulb in the 2004 Hyundai Santa Fe?Read more: How_do_you_replace_rear_window_brake_light_bulb_on_2004_Hyundai_Santa_f_e
How to replace a 97-02 Escort brake bulb. 1. Open the trunk. 2. Take the screws loose from the inside edge of the brake light housing. 3. There is a pin on the outside of the brake light housing that holds the housing onto the side of the car. Carefully pry the side of the housing away from the car, then pull the assembly off the back of the car. 4. Pull the bulb socket out of the housing and replace the bulb. 5. When putting the housing back on the car fit the pin in place first, then the 2 screws.
The brake lights are located in the trunk of a 1997 Acura Integra. To replace them open the trunk and find the plastic housing. Remove and replace the bulbs.
replacement of brake light bulb-- open trunk, look on inside of back of tail,brake light housing, there are retaining plastic screw on nuts, maybe covered by trunk lining of fabric. remove retaining nuts and push housing out, have someone to press brakes if not sure of which bulb to replace. locate and twist bulb housing out.
change the fuse if not replace flasher
well if you look on the brake lenses there should be screws on them take them off and your lens comes off
On a 1989 Acura Integra hatch back the brake lights are reached through the hatch itself. The brake lights housing are on the rear of the vehicle. Unplug the bulbs and replace them.
To replace the brake light on a 2001 Dodge Durango the light lens must be removed. It is held on by a clip on one side and a hinge on another. It opens like a door to access the brake light housing.
Just turn the housing the bulb is in and pull it out. Remove and replace the bulb the same way. For the rear lights, you have to push on a tab to release the housing the bulbs are in.
The lamp in the top brake light of a Toyota Highlander can be replaced by the locating the light housing from the trunk. Find the light cover and remove it to access the lights. Replace the bulbs.
if you mean to replace the "top" stop light. the one in the rear windshield, all you do is pull the brake light housing towards the seats, away from the window, it will pop out of place(careful not to pull out the wires) then just replace the bulb and pop it back into place over the meatl guides If you mean the one on the actual wing outside of the car and not on the inside, I also need that information.
Unscrew the housing from the sheet metal and remove the bulb socket from the back of the lens housing. Replace the bulb and re-attach.
you have to take the brake light out of the housing and then twist the amber bulb out
Inside the trunk: 1. Disconnect the power cable from the bulb housing. A screwdriver can help push in the tab. 2. Unscrew the two brass colored nuts to the right and left of the cable. Inside the car: 3. Pull the brake light away from the window 4. Twist the bulb housing counter-clockwise and pull it out 5. Pull the bulb out of the housing and replace
The brake light that is in the rear window of the Crown Victoria is accessible from inside the car. A small screw will loosen the housing, enabling access to the light.
To replace the rear corner lights on a 1998 Acura CL open the trunk. Find the brake light housing and disconnect the bulb. Install the new bulb.
Remove the wing nuts from inside the trunk. Just pull the housing out after.
You normally gain access to the bulb from inside the trunk.
my back brakes lights won't work but the one in the back window does