How do you replace the brake light bulb on a 2002 Jeep Grand Cherokee?

How to change the brake switch on a 2004 Jeep grand Cherokee Laredo

The 1993 Jeep grand Cherokee brake light switch simply plugs in and out. The brake light switch is located beneath the dashboard on the drivers side of the engine compartment.

The brake light fuse on a 2003 Jeep Grand Cherokee can be found by looking at the cover to the main fuse box. It identifies each fuse and its location.

To replace the brake light bulb you need to remove the whole light assembly. Once removed the change is simple.

A short in the brake light circuit.

Replace the bulb. There are usually 2 filaments in each bulb and one is most likely out. Replacing it should solve the problem

wjjeeps.com . they show how to replace every light and with what bulb

Failed circuit board on the back of the light.

If equipped, it is above the liftgate glass.

Replace the bulbs

You need to check the wiring for power to the bulbs.

They aren't. The brake light circuit is not connected with the headlight circuit.

its not a switch its a fuse check the fuse and the light fuse is under the driver side dash look in your manual for brake light fuse

passenger side fuse panel....#2

Either the brake light switch is out of adjustment, or has gone bad.

Why ? Just replace it.

The circuit board/socket in the tail light has failed.

This link should help. http://www.jeepforum.com/forum/f140/how-2005-2009-grand-cherokee-wk-fog-light-install-867728/

Mine simply needed brake fluid to fill it to the line indicated on the brake fliud container.

Defective or mal-adjusted stop light switch? Usually located at the upper end of the brake pedal under dash area

Check the bulbs in case they have fused, next check the fuse, and finally it could be the brake light switch which may need replacing

Tail lights-- You have to unscrew the three bolts inside the hatch, pull the tail light toward you, then turn the bulb at the top. Third brake light-- You have to take (4) screws out of the plastic trim around the top of the hatch inside. Then remove the plastic trim and turn whichever bulb is burnt out and replace it.

check your brake lights if they not worhing replace fuse or brake light switch

Check socket for power/ground corrosion Check stop light switch for power on one side Check fuse

Those lights are on because the computer has detected a fault and set a code. You will need to have the system checked with a scan tool.

Check ALL of the fuses with a test light then you will know they are good

Check the brake light switch located on the brake pedal lever. If there is power to the switch but nothing coming out replace it. Did you check the bulbs? Is there power to the rear sockets?

You need to replace your head light switchRutifo

I can answer for the 93 Jeep Grand Cherokee Limited. There are three 10mm nuts holding the lens on. Remove these nuts and the light sockets are twist and putt to gain access to the lights.

There are detailed instructions on the inside of the owners manual. You have to open the rear hatch and remove the screws on the light fixture.

The brake light switch is behind the brake pedal.

I had the same problem, all I did was replace the fitting that the bulb goes in with a new one ( $8.00 fix) and replaced the tail light and haven't had a problem since.

It is the one the owner's manual calls "brake system". I think number 26 maybe?

Remove the wing nuts from inside the trunk, the assembly will pop out.

To replace the brake light on a 2000 Ford Explorer, remove the screws holding the brake light in place. Gently, but firmly, pull the brake light out of the vehicle and replace with a new one.

Hard to see, but on my 96 Jeep Gr Cherokee there are two small screws next to each lamp on the outside.

How do you install passenger tail light kit for a 2004 grand cherokee?

APPLY BRAKES AND SEE IF BRAKE LIGHTS COME ON. IF NO BRAKE LIGHTS, REPLACE THE BRAKE LIGHT SWITCH LOCATED ON THE BRAKE PEDAL ARM AND THIS SHOULD ALLOW YOU TO SHIFT OUT OF PARK. IF THAT BRAKE LIGHT SWITCH IS BROKE, YOU WON'T BE ABLE TO GET IT OUT OF PARK

If Diamler hasen't messed that up too, the pre 1999 GC's have the bolts that hold the tail light on visible when tail hatch is lifted. If so, remove them, lift the light off, turn it over and there's the bulbs. Pop it out, replace it and put it back together. Good luck!

I had similar issues and just ended up replacing them (both) with Jeep replacements. Never had an issue afterwards.

There is a dead short to ground in the circuit.

How to replace a brake light on a nissan Tiida hatch back.

You already have a 3rd brake light behind the rear glass. Do you mean change the bulbs? If you do need to change the bulb then all you need to do is take off the paneling inside on the liftgate and you will have access to your lights.

To replace your brake light, you need to unscrew the brake cover from the inside of the trunk. Then you will be able to pull the old bulb out and replace it.

You can't. There's a circuit board connected to the shifter with LEDs on it. You have to replace the whole shifter. P/N # 52104149AC

most likely it is the high mount rear brake light. Open hatch and you will see where to remove the screw to access the bulb.

your left and right bulbs are problay bad they are two filament bulbs the park filiments are good and the brake filament is bad

Most lights on modern cars are function specific - one bulb for the brakes another for signalling, etc.... Find the bulb that is loose or blown and tighten or replace it. Answer Perhaps the first thing to consider would be that the bulb is burnt out or loose. Answer The following site discusses all lights in the Jeep Grand Cherokee, and includes pictures and diagrams on how to access them so that bulb changes can…

Open your tailgate and remove the bolts that hold the taillight on. I believe there is two of them. Carefully remove the light as the other end of the taillight is held in place by tabs. replace the light bulb/s and install by following in reverse.

how to replace the brake light switch at the pedal of a 2001 ford zx2