Head Gaskets and Valve Covers
Chevy Trailblazer
Radio

How do you replace the bulbs in the steering wheel radio controls in a 98 Grand Prix?

202122

Top Answer
User Avatar
Wiki User
Answered
2005-12-04 13:52:38
2005-12-04 13:52:38

For instructions on this task check out the following website. http://www.clubgp.com/cgi-asp/mods.asp?modid=112 Hope this helps. "G"

001
๐ŸŽƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Related Questions


Most steering wheel buttons bulbs are not serviceable, you must replace the button(switch) or the shole horn pad, most dash and switch bulbs are not serviceable


I was told that the bulbs are not replaceable. You have to replace the entire pad.


go to gm and replace each unit pops out with screwdriver


Take your car to the dealer or body shop.


The best place to get bulbs for behind the heater controls on a 2000 diesel Grand Vitara is directly from the manufacturer. An order can also be placed through a local dealer or auto parts store.


If a steering wheel has lights, there should be a way of accessing them. You want to look for some screws or pins on the back of the steering wheel. If none can be seen, the steering wheel may be pried apart to access the bulbs.


The bulbs can be replaced for the radio and heater controls on a 2000 Windstar SE by removing the plate over the heater controls. Some models need an Allen wrench for this and some models will need a Star wrench to remove the screws holding this plate on.


Remove the cover around the controls and you will see the bulbs inside the climate control unit. It just pulls off.


You have to remove the headlight which has 3 bolts(10mm socket&wrench) on top of it.


Check/replace bulbs Check sockets for power, ground, corrosion


pictures of how to change front signal bulbs on a 2004 grand prix pontiac


On secondary fuse box, under dash, between steering column and left side.


-- Without changing the bulbs, increase the voltage of the battery or power supply. -- If the bulbs are in series, take one out of the circuit, and replace it with a piece of wire. -- Replace incandescent bulbs with others whose filaments have lower resistance. -- Replace incandescent bulbs with fluorescent tubes. -- Replace incandescent bulbs with LEDs.


Check bulbs or may be problem in steering column Check bulbs or may be problem in steering column Check bulbs or may be problem in steering column


I know how, just need new bulbs. Do you have some? Mkrue@knology.net


The fog lights on a 2004 Jeep Grand Cherokee are accessed from the wheel wells. Remove the rivets for the dust covers to gain access to the lights. Twist off the bulbs and replace them.


To replace the bulbs in a 1997 Acura safely prop the hood open. Locate the front headlights and remove the old lights. Replace the bulbs.



In a 97-03, the bulbs are soldered into the circuit board of the heater controls. Remove the heater control assembly and disassemble it to the board. Desolder the bulbs and replace with new ones from either radio shack or corvetteradios.com. The bulbs are 12v but I don't know the wattage. CorvetteRadios has bulbs for the CD player as well which are similarly soldered into the circuit board on the face plate.


The 2002 Chevy Avalanche does not have user replaceable radio bulbs. The radio needs to be dismantled by a qualified technician to replace the bulbs.


Remove the instrument cluster and replace the bad bulbs. Take the battery cables off!Remove the upper and lower steering colum covers. Remove the four screws on the cover. Tke the screws out of the cluster and turn it over. Replace the bad bulbs. Had to replace the whole cluster on mine as the speedometer and the heat guage were kaput!


This is a bit dissapointing, but.... you dont in my 98 park avenue the "bulbs" that light up the A/C control are led bulbs, attached to a circuit board. So the only way to really replace them is to either get a new heater control, or solider new led lights to the circuit board.


Start with pulling the steering wheel all the way down (use the handle under the steering wheel), then pull the plastic that is under the cluster out towards you, under the plastic cover are two screws that you have to take out. After that you just need to wiggle the cluster out, and replace the bulbs.


Perhaps a short in steering column Remove all bulbs and check fixtures for corrosion Replace bulbs one at a time until fuse blows and further check or replace that fixture


To replace the brake light bulbs on a VW Polo, pull away the carpeting in the trunk, unscrew the bolt holding the lights on, and disconnect the wiring. Replace the bulbs, put the wiring and bolts back, then replace the carpeting.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.