answersLogoWhite

0

  • Ford Contour
  • VW Jetta
  • Crankshaft Sensors
  • 1995-2005 Chevy Cavaliers

How do you replace the camshaft position sensor on a 98 Ford Contour 4-cylinderinder?


Top Answer
User Avatar
Wiki User
Answered 2015-07-15 21:34:22

Simon from Montreal

The camshaft sensor is located at the back of the head on driver side. Remove the wire,unscrew the sensor,screw the new sensor in the head and put the wire back on the sensor.Pretty easy job!

Mike From Des Moines

The camshaft sensor is not in the back on the 98 4 cyl its right in front. All you need to do is take off the 3 bolts on the top of the heat shield and pull it back a bit and it will be right there.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar
User Avatar

Anonymous

2020-06-26 19:28:21

How do you remove the sensor

Your Answer

Loading...

Still have questions?

Related Questions

How do you replace replace the camshaft position sensor?

In order to replace the camshaft position sensor, you would need to disconnect the electrical plug holding it in. Using a socket, hold down the bolt and remove the camshaft position sensor.


How do you replace the camshaft position sensor on a 1997 Plymouth voyager 3 L?

how do you replace the camshaft position sensor on a 1997 plymouth voyager 3l


Where is the camshaft position sensor located on a 1999 Oldsmobile Intrigue and how do you replace it?

where is the camshaft position sensor located on a 1999 Oldsmobile intrigue


How do you replace a camshaft position sensor on a 2000 Nissan Xterra?

How do u replace the camshaft sensor for a 2000 Nissan xterra 3.3L and where is its locatoin


P1345 crankshaft position camshaft position correlation?

Replace the crankshaft and camshaft senors and then clear the codes with an oBD II engine scanner and that will fix it.


If you replaced the camshaft position sensor should you replace the crankshaft position?

I changed only the camshaft position sensor on my 2000 Kia Sportage. So I don't think so.


How to replace camshaft position sensor for vw jetta 1999?

how to remplace position of oxigen sensor


Where is the camshaft position sensor on a 2006 Kia Sorento?

do you need to take off the timing belt to replace a camshaft position sensor on a 2006 kia sorento


VW Beetle 2.0 camshaft senors 2001?

Show me how to replace the camshaft position sensor on a 2000 volkswagen new beetle


How do you replace camshaft position sensor on a 2006 Nissan xterra 4.0 v6?

camshaft location on a 06 xterra bank 2


1997 contour that has a 2.0 zetec in it and it gives me a p1383 code i timed it with no improvement i wanted to know if a bad injector could give this code thanks for any help?

Trouble code P1383 means: Camshaft Position Timing Over Retarded (Bank 1) Replace the camshaft sensor


How do you replace the camshaft positioning sensor ml27 cdi?

the camshaft position sensor is on the left side of the engine , at back on the upper side . you have to demont the conector , than unscrew and replace it


Where is the camshaft position sensor on a 1996 Nissan Sentra?

in the distributor, you have to replace the whole unit.


How do i install a 1997 dodge caravan 3.0 camshaft position sensor?

If I'm not mistaken, I think the camshaft position sensor on these engines is built into the distributor. You'd have to replace the whole thing.


Where can you find the camshaft position sensor on a Nissan Altima?

It is located on the backside of the engine. Go to youtube and type in how to replace camshaft sensor on 2005 Nissan altima and it will show where it is and how to replace it, that is how I did my one.


How do you replace the camshaft position sensor on Nissan Altima?

The camshaft position sensor is located near the thermostat housing. You should replace the crankshaft position sensor as well. This one is much harder to locate....it is on the backside of the engine that is between the firewall and the engine block. Both use the same sensor.


How do you replace the camshaft position sensor on a Chevrolet tracker?

model year and engine size are relevant to the question.


How do you replace 99 Chevy s10 camshaft position sensor?

Depends on which engine you have. More info please.


How do you replace the camshaft position sensor on 2004 suzuki forenza?

One would replace the camshaft position sensor on a 2004 Suzuki Forenza by taking it to a certified auto mechanic. The mechanic would then check out and repair the issue, thereby rendering the car back to a serviceable condition.


If the diagnosis of your engine diagnosis shows the followind. camshaft position sensor A circiut what do you do?

Replace position a sensor and your problem should be takin care of.


1994 Plymouth Sundance trouble code 11?

Code 11 means no camshaft position sensor signal detected during engine crankingFix : Replace the camshaft sensor


Where is the camshaft position sensor on a 1996 Chrysler Cirrus V6 2.5 liter?

It is in the distributor, you have to buy a distributor to replace.


Where are the camshaft position sensor located on a 2003 GMC Envoy and how do you replace it?

[img]http://memimage.cardomain.net/member_images/7/web/2551000-2551999/2551515_94_full.jpg[/img] number 2 is the camshaft position sensor, number three is the camshaft position actuator From my understanding th replacement is pretty easy. I have not replaced one, so I wont try and tell you how to replace it, however check out www.trailvoy.com for answers to any Envoy/Trailblazer question.


Does a 1999 Chrysler cirrus have a camshaft position sensor?

Yea, the crankshaft sensor is under the distributor and the camshaft sensor is inside the distributor, you cannot change it so you will have to replace the whole distributor.


Where are the crankshaft position sensor and the camshaft position sensor located on a 4cyl 95 Toyota Camry?

The crankshaft position sensor must be behind the timing belt cover next to the crankshaft and behind the crankshaft pulley. The camshaft position sensor is again under the timing belt cover next to the camshaft and behind and the camshaft pulley. Is it the same place in 2000 Camry 4Cyl? Do you have pictures of the location? Hard or easy to replace, and what tools do I need? Thanks alot