answersLogoWhite

0


Best Answer
Copy

GM seriously over-complicated something which should have been so simple. You can only get to the light through an access panel located in the shroud under the front bumper. Because the car sits so low to the ground, this requires you to jack the car up (always use jack stands), and then remove the two screws on the access panel and fold it out of the way. You then have to reach up inside the bumper to the back of the light. Squeeze the tab on the side of the socket and twist the socket to remove it from the turn signal housing. The light bulb itself can then be pulled straight out of the socket without twisting.

.

update, 2009

I just managed to change the turn signal light using a foot long screwdriver to push in the tab on the socket while simultaneously pushing on the other side of the socket with the two fingers that could just touch the socket opposite the tap. Look to the side of the headlight housing and you can just see the socket. It is on top of the light housing for the turn signal and the bulb sticks down. You will need to remove any watch and roll up your sleeves to reach the housing. I also pushed sideways with the screwdriver while holding in the tab with the screwdriver. Once it broke free is was easy to turn and remove and replace with a new bulb.

Same same on my 2000 Camaro.

I first used my phone camera and flashlight to get a good view of what I was feeling with the fingertips. Then with small flashlight resting on frame rail I could just see the goal (view between headlight housings). The foot long screwdriver goes through this peep hole, press the tab, push c'clockwise, 1/8 turn and presto it was loose. Note, flat blade screwdriver must be oriented so it holds tab down AND pushes sideways. Oriented the other way it slips off the tap. Socket can also be viewed looking almost horizontal from center line of car. Good luck! Change both while your at it.

User Avatar

Wiki User

โˆ™ 2015-07-14 15:05:45
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you replace the front turn signal bulb located on a 2001 Chevy Camaro?
Write your answer...
Submit

Related Questions

Where is the turn signal flasher unit located on a 1984 Chevy Camaro Z28?

The 1984 Chevy Camaro turn signal flasher unit is located beneath the drivers side dashboard. The turn signal flasher unit will be above the brake pedal.


Where is the turn signal flasher located on a 1995 Camaro?

The 1995 Chevy Camaro turn signal flasher relay switch can be found beneath the drivers side dashboard. The turn signal flasher relay switch will be between the gas pedal and the brake pedal.


Where is the fuel filter located and how do you replace it on a 1990 Chevy Camaro?

In front of left rear tire under body


How do you replace a water pump on a 1996 Chevy Camaro z28?

How can do I replace a water pump on a 96 camaro z28


How do you replace the turn signal switch located on a 1998 Chevy Lumina?

pull the steering wheel


How do you replace the front turn signal bulb located on a 2001 Chevy suburban?

If you remove the headlight assembly you will have access to the turn signal bulb.


How do you replace the turn signal switch located on a 1986 Chevy Camaro?

it's under the dash on the drivers side there are 2 under there one for the blinker and another for the emr. lights the one for the turn signals is cloest to the door i believe.


Where is the horn located on a 1994 Chevy Camaro?

The 1994 Chevy Camaro horn is located in the front of the engine compartment. The horn will be on the right hand side of the radiator.


Where is the turn signal flasher unit located on a 1994 Chevy Camaro?

underneath driver's side lower dash plate. it will be on your right hand side.


Where is fuse located for the blinkers on a Chevy Camaro?

WHAT YEAR ?????


How do you replace the fuel filter located on a 1995 Chevy Camaro?

remove neg battery terminal, and the gas cap then replace the filter. Its under the vehicle towasds the gas tank


How do you replace the clutch on a 1999 Chevy Camaro SS?

Take it to a mechanic.


2002 Chevy cavalier turn signal bulb replace?

How do you replace a turn signal bulb in a 1998 cavalier


How do you replace turn signal flasher on a 1998 Chevy blazer?

there located behind the dash below the radio to the left of the ashtray. side by side,hazzard and turn signal


Where is the ignition module located on a 1980 Chevy Camaro?

It is inside the distributor


Where is a blower motor located in a 1994 Chevy Camaro?

under the dash


Where is the clutch slave cylinder located on a 1994 Chevy Camaro?

should be located on the bell housing


Where is the signal flasher located on a 2008 chevy avalanche?

The turn signal flasher on a 2008 Chevy Avalanche is located inside a panel close to the gas pedal.


How do you replace the fuel pump on a 1987 Chevy Camaro?

You must remove the fuel tank.


How many does a Chevy Camaro have and where are they located?

How many what does a Camaro have? seats? 2 in the front lights? 4 please be more specific.


How do you replace the turn signal switch located on a 1992 Chevy Corsica?

Since the 92 Chevy Corsica is equipped with SRS (Saftey Restraint System), ie: Airbags, which is located in the steering wheel. In order to replace the turn signal switch you must remove the steering wheel. Therefore I would only highly advise you to take it to a dealer to have this done.


How do you replace the turn signal switch on a 2003 Chevy Silverado.?

The 2003 Chevrolet Silverado turn signal switch is located below the dashboard, on the drivers side of the passenger compartment. The turn signal switch simply plugs in and out.


Where is the Chevy Camaro 1999 speed sensor located?

it's built into the computer.


Where is the starter relay located on a 1996 3.8l Chevy Camaro?

The starter relay on a 1996 Chevy 3.8l Camaro is located in the engine compartment along the left side. It sends power to operate the starter and prevents overloads.


Where is the starter located 1993 Chevy Camaro?

The 1993 Chevy Camaro starter can be found on the right hand side of the engine. You can follow the positive at three cable directly to the starter.