answersLogoWhite

0


Best Answer
Copy

It looks as if I'll have to crawl under the front of the car to access the bulb to replace it.

User Avatar

Wiki User

โˆ™ 2009-05-31 20:02:32
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you replace the front turn signal on a 2001 2dr sunfire not a part of the headlight assembly?
Write your answer...
Submit

Related Questions

How do you replace the front turn signal bulb located on a 1999 Chevy Blazer S-10?

Remove the headlight assembly above the faulty signal bulb. This will give you access to the signal bulb socket. To remove the headlight assembly, open the hood, stand in front of the headlight assembly, notice two black tabs sticking up behind the headlight assembly inside the radiator support. Pull up and wiggle the tabs to remove them, this will release the headlight assembly. You can now wiggle the headlight assembly out to gain access to the signal bulb socket for replacement.


How do you replace the front turn signal bulb located on a 2001 Chevy suburban?

If you remove the headlight assembly you will have access to the turn signal bulb.


How do you replace the headlight bulb on a 2003 dodge caravan?

1) open the hood. 2) Carefully remove the three screws holding the headlight assembly in place. In my case the screws were black. Be careful as they are screwed into plastic. 3) Carefully slide the headlight assembly out. At this point you can replace the headlight bulb, turn signal bulb, or the entire headlight assembly. To replace the headlight bulb turn the collar holding the bulb in counter clockwise. Pull the bulb out of the headlight assembly. Replace the bulb. Insert the bulb into the headlight assembly insert the collar and turn clockwise until it locks. 4) Carefully insert the headlight assembly back into place. 5) Replace the three screws removed in step 2 being carefull not to over tighten.


How do you replace the headlight bulb located on a 2007 Dodge Caravan?

1) open the hood. 2) Carefully remove the three screws holding the headlight assembly in place. In my case the screws were black. Be careful as they are screwed into plastic. 3) Carefully slide the headlight assembly out. At this point you can replace the headlight bulb, turn signal bulb, or the entire headlight assembly. To replace the headlight bulb turn the collar holding the bulb in counter clockwise. Pull the bulb out of the headlight assembly. Replace the bulb. Insert the bulb into the headlight assembly insert the collar and turn clockwise until it locks. 4) Carefully insert the headlight assembly back into place. 5) Replace the three screws removed in step 2 being carefull not to over tighten.


How do you replace the headlight located on a 1997 Chevy pickup?

If you're removing the headlight assembly,you'll need to remove the turn signal light lenses,then the grill. From there you will see four bolts to each headlight assembly. It's pretty straight forward from there.


How to replace the front turn signal bulb on a 2000 blazer s-10?

Open the hood, remove the two tabs that lock the headlight assembly in place, remove the headlight assembly, doing this will give you access to the signal light socket for bulb replacement.


How do you fit a replacement headlight bulb on an s type jaguar?

To replace the headlight bulb in an S type Jaguar, you will first have to remove the plastic cover across the top of the assembly. After moving the turn signal bulb assembly out of the way, you then remove the second plastic cover from behind the assembly and replace the bulb from there.


How do you replace the headlight bulb located on a 2000 Chevy Venture?

Hi, You have to remove the entire headlight assembly to get to the bulb, which is located in the back of the assembly. There are three wing nuts that hold the assembly in, and those will have to be removed. Then remove the side signal assembly first, then the headlight assembly. I have provided a link that shows exactly how this is done and where these wing nuts are. Good Luck


How do you replace the front turn signal light on a 2001 BMW X5?

you must completely remove the complete front headlight assembly


How do you replace the front turn signal bulb on a 2000 Oldsmobile silhoette?

Look back on responses to how to change headlight or turn signal assemblies on this page. Do the same thing, just twist out the bulb and twist in the new and reassembe. You must remove the turn signal assembly and the headlight assembly must be loosened. But it is very easy.


How do you replace the front turn signal bulb located on a 2001 Chevy S-10?

Remove the headlight assembly above the bad bulb to gain access to the burned out bulb. To remove the headlight assembly, open the hood, locate and remove the two tabs that lock and hold the assembly in place, with those tabs removed you can wiggle the headlight assembly out in the open. Now you can reach in and r & r the burned out signal bulb


How do you replace the front turn signal bulb located on a 2002 Buick Park Avenue?

Remove headlight assembly to access bulb/socket.


How do you replace the front turn signal bulbs on a 1999 Pontiac Sunfire?

On a 99 sunfire if you open the hood there is a plastic piece that is attached by little plastic fastners that cover the radiator and right where the hood latch is. Youll need to remove these fastners by placing a wide flat head screw driver between the circular head of the fastner and the circular base of the fastner and pop them out on by one. try to remove one of the fastners in a inconspicuos location if your not sure how to remove them. its fairly easy once you know how they work. then you will need a socket set. there are two bolts on the top of the headlight but under the plastic peice that hold the headlights in place. remove these two bolts (two for each headlight) this will allow you to remove the headlight assembly but don't pull it completely out there are wires that run in to the headlight to supply power to you bulbs. After that under the headlights is the turn signal assembly you should be able to replace the bulb buy unlocking it from the turn signal with out removing the turn signal assembly itself. To change ""other bulbs"" such as the third brake lights on the sunfire you have to have a star key to remove the assembly and gain access to the bulb for replacment. Hope this helps BLUE


How do you replace a turn signal bulb 2005 Montana?

To replace the front turn signal bulb in a 2005 Montana, you have to access it from the engine compartment. Undo the front headlight assembly as per the instructions noted elsewhere. There is one screw (machine Head) on the outboard side of the headlight assembly, and one 'thumb screw' on the inner side to the assembly. I found it difficult to remove the headlight assembly, and I have found you don't have to. (You can break the housing, so don't try taking it right out) Just loosen it enough to get your hand behind the assembly. I would also suggest you remove the plastic fasteners from the top of the front bezel in order to make loosening the headlight assembly easier, and to prevent the possibility of damaging or breaking the front bezel. The plastic fasteners are easily removed with just a pair of pliers. Once the headlight assembly has been moved forward slightly, you can get your hand down the opening, and feel for the turn signal lamp assembly. Twist to remove. There is enough wire in the harness to bring the lamp assembly to 'the surface' where you can replace the bulb easily. Replace bulb and test. After testing, replace headlight, and then plastic fasteners at the top of the front bezel.


How do you replace the headlights in the 2003 Dodge Grand Caravan?

I need to replace the bulb on the driver side of my 2003 Dodge Grand Caravan. After searching this forum I found a similar question regarding the 2000 Caravan. It talked about under the hood removing three screws and pulling out the headlight assembly. I tried this and it worked on the 2003. 1) open the hood. 2) Carefully remove the three screws holding the headlight assembly in place. In my case the screws were black. Be careful as they are screwed into plastic. 3) Carefully slide the headlight assembly out. At this point you can replace the headlight bulb, turn signal bulb, or the entire headlight assembly. To replace the headlight bulb turn the collar holding the bulb in counter clockwise. Pull the bulb out of the headlight assembly. Replace the bulb. Insert the bulb into the headlight assembly insert the collar and turn clockwise until it locks. 4) Carefully insert the headlight assembly back into place. 5) Replace the three screws removed in step 2 being carefull not to over tighten.


How do you replace the front turn signal indicator assembly on a 1999 S70?

Just had to do this. At the top outside edge of the headlight assembly, where it meets the turn signal assembly, there is a space you can put a finger through and push down a plastic tab. It's not hard to see if you know it is there. With the tab pushed down, the whole turn signal assembly can be pulled forward and out.


How do you replace a 2000 Oldsmobile Intrigue headlight assembly?

The plastic headlight assembly is held in by two clips. Pull them up to release the assembly. The headlights and turn signal lamps are quarter (90°) twist-in sockets, and also need to be disconnected before you can remove the entire assembly from the car. The bulbs plug into the sockets once they are removed from the assembly.


How do you replace front turn signal assembly in a 2001 Subaru forester?

Turn signal lever assembly can be replaced without removing the steering wheel. See instructions at the attached link question about replacing the headlight switch on a 1999 Subaru Forester.


How do you replace the front turn signal bulb in a 1999 Oldsmobile Silhouette?

you have to remove the whole headlamp assembly to get to the turn signal bulb pull the headlight assembly straight out it is fairly easy There are two wing nuts on top of the unit that must be removed.


How do you change a front turn signal in a 2005 Malibu Chevy?

there are two screws holding the light assembly to the car. Remove the two and replace after removing headlight


How do you replace headlight bulb 2004 Chevy Venture?

Hi, Replacing the headlight bulb on these vans is relatively easy. Once you open the hood, you will see three wing nuts that hold the turn signal assembly and the headlight assembly in place. The turn signal assembly has to be removed first by removing the wing nut that is closest to the outside of the van and then pulling the turn signal assembly straight out. It should come out easily. Next, remove the other two wing nuts and pull the headlight assembly up and out (in that order). Once you have the assembly out, place it lens side down on a soft cloth. There is supposed to be nitrogen gas inside the assembly, so keeping it face down will help to prevent the escape of that gas. To remove the bulb, just turn the bulb socket counter clockwise and it should come right out. Just replace the bulb with a new one and reverse the whole process to reinstall the headlamp assembly and the turn signal assembly. I have included a link that shows the headlight and three wing nuts. Good Luck, Greg


How to replace the right turn signal light assembly in a '94 Toyota Tercel?

Unscrew the screw that attaches it to the headlight. Pop it out. Twist bulb so it comes out.


How do you replace the front turn signal bulb located on a 2000 Chevy Venture?

No tools are required, there are three black wing nuts above the headlight, take these off and wiggle the turn signal light assembly until it moves past the headlight assembly. The turn signal assembly is located by two pins at the rear so pull it forward a bit as you wiggle it. The bulb just pulls out and cant be put in backwards, so its all very easy. (It is only necessary to remove the bolt that holds the turn signal assembly in place if you don't need to replace the headlamp. The assembly may then be removed by pulling forward on it to disengage the tabs. It is also easier to get it back into place if the headlamp assembly is still bolted in--align the tab and guide in the back and push the assembly straight back to engage. Then replace the bolt.)


How do you replace the front signal bulb on 1996 ford mustang?

Looking at the headlight assembly, on the side of the burnt out directional bulb, look at the back of the headlight. To the side of the headlight adjusters, on the side wall of the wheel well you will see a 10 mm nut. That nut is the only thing holding the directional assembly on. Take that nut off and jiggle the assembly. It will pull out to the side. Replace bulb and reinsert the assembly. Be carefull that you get the plastic bayonet shaft into the correct hole along with the stud that has the nut on it. tata G


How do you replace headlight lamp on 2004 Chevy Venture?

Hi,The headlamp bulb is relatively easy to replace in these vans. What you have to do is remove the turn signal assembly first, and then the headlamp assembly. This is done by removing 3 wing nuts that hold the assemblies in, and then pulling the turn signal assembly straight out, followed by the headlamp assembly. The headlamp assembly has to be lifted UP and then Out.Once you have the assembly out, the headlight bulb can be unscrewed from the back of the assembly and replaced. Be careful not to get any oil from your fingers on the new bulb, as that will heat up when the light is on and decrease the lifetime of the bulb.I have included a link below that shows pictures of the assemblies and how to removed them.Take Care, Greg