answersLogoWhite

0


Best Answer

2.2L engine

Caution Relieve the fuel system pressure before servicing fuel system components in order to reduce the risk of fire and personal injury.

After relieving the system pressure, a small amount of fuel may be released when servicing the fuel lines or connections. In order to reduce the chance of personal injury, cover the regulator and the fuel line fittings with a shop towel before disconnecting. This will catch any fuel that may leak out. Place the towel in an approved container when the disconnection is complete.

Disconnect the negative battery cable.

Caution Before servicing any electrical component, the ignition key must be in the OFF or LOCK position and all electrical loads must be OFF, unless instructed otherwise in these procedures. If a tool or equipment could easily come in contact with a live exposed electrical terminal, also disconnect the negative battery cable. Failure to follow these precautions may cause personal injury and/or damage to the vehicle or its components.

Remove the air cleaner outlet resonator mounting screw.

Disconnect the air cleaner outlet resonator clamp at the throttle body.

Remove the air cleaner outlet duct from air cleaner outlet resonator and air cleaner assembly.

Disconnect the crankcase vent hose clamp and the crankcase vent hose from the top of the engine.

Remove the air cleaner outlet resonator.

Remove the fuel rail bracket.

Remove the fuel injector electrical connectors by pushing in the wire connector clip and pulling the electrical connector away from the fuel injector.

Remove the fuel feed inlet pipe quick connect.

Remove the fuel return pipe from the fuel pressure regulator.

Remove the fuel rail attaching bolts.

Remove the fuel rail assembly from the cylinder head.

Remove the fuel injector retaining clip.

Remove the fuel injector.

Important Visually inspect the fuel injector to see if the upper O-ring was also removed, if not, remove the O-ring from the fuel rail assembly.

2.4L engine

Caution Relieve the fuel system pressure before servicing fuel system components in order to reduce the risk of fire and personal injury.

After relieving the system pressure, a small amount of fuel may be released when servicing the fuel lines or connections. In order to reduce the chance of personal injury, cover the regulator and the fuel line fittings with a shop towel before disconnecting. This will catch any fuel that may leak out. Place the towel in an approved container when the disconnection is complete.

Disconnect the negative battery cable.

Caution Before servicing any electrical component, the ignition key must be in the OFF or LOCK position and all electrical loads must be OFF, unless instructed otherwise in these procedures. If a tool or equipment could easily come in contact with a live exposed electrical terminal, also disconnect the negative battery cable. Failure to follow these precautions may cause personal injury and/or damage to the vehicle or its components.

Remove the air cleaner outlet resonator mounting screw.

Disconnect the air cleaner outlet resonator clamp at the throttle body.

Remove the air cleaner outlet duct from air cleaner outlet resonator and air cleaner assembly.

Disconnect the crankcase vent hose clamp and the crankcase vent hose from the top of the engine.

Remove the air cleaner outlet resonator.

Remove the vacuum hose at the fuel pressure regulator.

Remove the Camshaft Position sensor electrical connector.

Remove the fuel injector electrical connector retaining clips.

Remove the injector electrical connectors.

Remove the fuel inlet pipe at the fuel rail. (Use a backup wrench on the fuel rail inlet fitting to prevent it from turning).

Remove the fuel pipe retainer clip nut (if so equipped).

Remove the fuel pipe retainer clip bolt.

Remove the fuel rail attaching bolts.

Lift the fuel rail assembly from the cylinder head.

Loosen the fuel return pipe retaining bracket attaching screw. (Rotate the retaining bracket to allow fuel pipe to be removed.)

Remove the fuel return pipe (2) from the fuel pressure regulator.

Remove the inlet and the return pipe assemblies. Discard O-ring.

Remove the fuel rail assembly.

User Avatar

Wiki User

โˆ™ 2015-07-15 19:10:01
This answer is:
User Avatar
Study guides

Add your answer:

Earn +20 pts
Q: How do you replace the fuel injectors on a 99 Cavalier?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you replace fuel injectors on 99 trooper?

99 isuzu trooper smell gasoline in the engine compartment


Where is the fuel reg valve on a 99 Z24 cavalier?

Above the alternator. It is round and has a vacuum line connected to it. The fuel rail has to be removed to replace it.


How many fuel injectors does a 99 nissan maxima have?

6


How do you replace the thermostat located on a 1994 Chevy Cavalier?

where do i find the thermostat for 99 cavalier


How to unclog injectors on a 99 Tahoe?

It is important to have functioning fuel injectors. A person can unclog their fuel injectors by buying fuel injector cleaner and putting it in their gas tank every time it almost empty.


How many fuel injectors does a 99 grand am SE have?

One per cylinder.


Why is the fuel gauge always at empty on a 99 cavalier?

It is likely that your fuel sending unit has gone bad. It is located in the fuel tank. Some tanks have an access hole and others require the removal of the fuel tank to replace it.


Can you swap Ford Escort fuel injectors on a 99 Ford Escort ZX2?

No they are different. The zx2 injectors wont fit an Escort head.


How much is it to buy a fuel pump for a 99 cavalier car?

how much 4 the pump.


Can you replace your 2.2 liter with a 2.4 liter echotech engine on a 99 Chevy cavalier?

No


How do you replace drivers side headlight bulb 1999 cavalier?

i wanted to know how to change head light bulb of 99 cavalier


What Cause Jerking on a 99 Mercury Cougar?

The primary cause for jerking on a 99 Mercury Cougar is the engine not getting enough fuel. This can be a sign of a clogged fuel filter, bad fuel pump, or clogged fuel injectors.

People also asked