To replace the head gasket on a 1994 Oldsmobile Cutlass 3.4L, everything on the top of the motor needs to be removed. The battery should be unhooked first, then the valve covers, then the head itself. Replace the new gasket after cleaning the old gunk off from the first gasket. It is a good idea to take a picture before, during, and after, to make sure everything is hooked up like it should be. One note, the valve cover gasket will also have to be replaced after removal.
What size engine? 3.1 or 3100? yes there is a difference. email@example.com
remove old thermostat and replace with new thermostat and gasket
A transmission fluid leak means that the plug may need to be replace, or the seal or gasket may need to be replace. As it could be caused by a work seal, or gasket, or a loose plug.
Possibilities are low coolant, defective radiator, leaky hoses, blown head gasket...
If there are no visible leaks....a blown head gasket.
replace head gasket
Remove the 1995 Oldsmobile Cutlass intake manifold retaining bolts. The manifold will come off. Remove the old gasket. Clean the surface. Put the new intake gasket and tighten the intake manifold retaining bolts.
There are 2 of them. They are sandwiched between the heads and the engine block. In order to replace them the intake manifold and heads must be removed and exhaust manifold disconnected. Always replace both of them on a V6.
To replace the oil pan gasket on the Cavalier you need the tool box to open where it is located. After opening, you can proceed to replace the oil pan gasket.
the thermistat is located inside the upper radiator hose, where it connects to the motor. have the car off and cold. just unbolt it and pull the old w/gasket. replace with new and gasket. bolt in. the attach hose. top off antifreeze
Mechanical engine mount? Remove old one Install new making sure cam is under lever to activate replace mounting gasket and fuel lines Mechanical engine mount? Remove old one Install new making sure cam is under lever to activate replace mounting gasket and fuel lines
The gasket on an Oldsmobile Bravada is changed by removing the retaining bolts, taking off the cover, and peeling the gasket off. The surface is then cleaned and a new gasket put in place.
I have a 2002 Olds Silhouette and had to replace the head gasket set 2 years ago. It raun around $1,700.00
located at the end of the upper radiator hose. remove two bolts, replace with new parts remember to replace the gasket.
It cost us about $700 cnd. That was a shop that charged about $75/hr.
Depends on where you live and who fixes it. Expect to pay at least $500 and up.
Follow the top radiator hose over to the engine and where it connects to the thermostat housing. There should be two bolts holding the housing to the motor. Remove the housing and replace the thermostat and gasket. The larger side of the thermo goes in the engine.
The cost to replace the head gasket of a 2000 Oldsmobile Alero costs between $20 to $190. This depends on where the part is bought, the brand of the park and any costs concerning labor or shipping.
You will need to remove the intake and the exhaust manifolds and then you can remove the heads to replace the gaskets.
To change the water pump simply remove the bolts from the waterpump, pull it off and replace with new. The power steering pump will need to be loosened and moved aside to remove one bolt. Clean old gasket from engine block and replace with new gasket and replace with new waterpump.
take it to your local garage
Basic mechanics sockets, ratchets, and extensions, plus a good torque wrench.
The cost of the head gasket itself would be anywhere from approximately $20 - $40 per piece (there are two head gaskets, as 1995 Olds Cutlass Supreme has a V6 engine) depending on whether you have the 3.1L or 3.4L DOHC engine. Most of the cost will go to labor; it is a time-consuming job. Best to call a few shops to compare and get estimates on actual labor and parts prices. If anyone has more detail on labor cost, please chime in.
Any parts store can provide you with the correct gasket.
Replacing the head gasket on any vehicle is a long and complicated process, however if you wish to see basic step-by-step instructions go to the related question on the right side of the page "How do you replace a head gasket?"