answersLogoWhite

0


Best Answer
Copy

Real simple, just open the hood disconnect the wire harness from the bulb, and then remove the screws holding it in. There's only two of them according to the manual.

There will be a total of 2 screws, 1 bolt, and 2 nuts to remove the assembly (and, of course, disconnect the two bulbs). The 2 screws are Phillips head and the bolt will need a 10mm wrench (they are on top). The 2 nuts are also 10mm and are behind the clear turn light rounding off the the side of the headlight assembly. Only one screw holds that in and a peg in that light faces straight ahead, so remove that by forcing that light forward. The assembly now only has a friction pivot on the bottom holding it, this also must be pryed straight forward. They will not pop off easily as they are a tight fit.

User Avatar

Wiki User

โˆ™ 2011-09-12 20:58:26
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you replace the headlight assembly located on a 1994 Geo Prizm?
Write your answer...
Submit

Related Questions

How do you replace the headlight bulb located on a 1998 Chevrolet Prizm?

the headlight assembly needs to come out in order to change the bulb ive had to do that to my 98 as well.


How do you replace cigarette lighter assembly in 2001 Chevy Prizm?

Remove the retaining ring on the top of the cigarette lighter assembly. Pull the cigarette lighter assembly out and remove the wiring harness from the back of the assembly. Reverse the process to install the new cigarette lighter assembly.


How do you replace the headlight bulb located on a 2001 Chevy Prizm?

The bulb assembly needs to be removed from the front of the vehicle. Open the hood, and you will see that the entire plastic headlight assembly is held in place by a few hex head screws. Once these are removed the entire assembly can be lifted out, giving you access to the lamp socket. Replace the lamp (bulb)and reinstall. NOTE _ Be careful not to drop the screws in between the radiator and the grill, as they are hard to retrieve and usually get stuck on the body panel below the bumper. **you can actually avoid taking out the entire headlight if you just remove anything in the way of reaching behind the assembly. on the right side, it would be the fuse box, on the left side you can probably just reach behind if your hands aren't too large. then remove the rubber seal by prying it off. there is a spring clip that holds in the bulb, remove that by sliding it out from behind the bulb, then remove the bulb and replace.


How do you replace the timing belt on a 1994 Geo Prizm 1.6?

How do you replace the timing belt on a 1994 Geo Prizm 1.6?


Where is the vacuum diagram located on 1990 Geo Prizm?

where is the vacuum diagram located on 1995 geo prizm


How do you replace the water pump in a 93 geo prizm?

See the related question: How do I replace the water pump on a 1993 Geo Prizm 1.8L?


Where is the heater control valve located on a 1998 prizm?

Locating on a 1998 prizm - fine idea


How do you replace the dash lights on a 1999 Prizm?

See: "How do you change the instrument panel lamps on a 2002 Chevy Prizm?" in Wiki s.The question you ask is too involved for a proper answer. You need to go to a car parts store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.Looking at the guage assembly, remove the screws holding the dashboard bezzel in place [screws are located top front by steering columb]tilt assembly forward, unscrew bulbs


Can anyone tell me where the horn is under the hood of a 1998 Chevy Prizm?

It is behind the headlight on some cars.


How do you replace the turn signal on a 1998 Prizm?

pep pep


How do you replace the alternator on a 1994 Geo Prizm?

From under the car.


How replace a motor mount on a 1997 geo prizm?

Remove the old mount & replace with the new.


Where is the oil pressure switch on a 1994 GEO Prizm?

where is located the oil pressure switch for 94 geo prizm


Will a Toyota corolla headlight 1998-2000 fit a Chevy Prizm 1998-2002?

yes


What type of fuel filter does a 2000 Chevy Prizm have?

It is located inside the gas tank. Dealer once quoted $500 to replace the entire tank unit. It is located inside the gas tank. Dealer once quoted $500 to replace the entire tank unit.


Where is the fusebox located in a 1994 Geo Prizm LSI?

I have a 1993 Geo Prizm, and there is a fuse block is located to the left of your left leg; on the plastic panel. There is a pull out access door there.


How do you replace 94 geo prizm water pump hose?

If you are referring to the water inlet hose on the back of the water pump you can use this question as reference. How do i replace the water pump on a 1993 Geo Prizm 1.8L?


How do you replace a speedometer head on a geo prizm?

It easy to replace the whole custer, screws just hold it in place.


How do you change the front low beam light on the driver side of a 1994 geo prizm?

Remove air intake duct to gain access to the back of the headlight housing then press lock release and unplug the electrical connector, rotate the bulb assembly counterclockwise and withdraw it from the headlight housing. When reassembling be careful not to touch the glass part of the bulb, if you do clean with alcohol and allow to dry.


How do you fix a PVC valve on a 1997 geo prizm?

You don't fix it, you replace it.


Where is the thermostat located on a 2001 Chevy Prizm?

It is located under the hood inside the radiator hose.


Where are the fuse boxes on a 1993 geo prizm?

There are a few fuse boxes located on a 1993 Geo Prizm. The main fuse boxes are located under the driver side dash on in the engine compartment.


Where is the ecu located on a 95 Geo Prizm?

On my 1992 Prizm the ECU is behind the center console; just beneath the back of the radio/ashtray.


How do you replace the thermostat located on a 1993 Geo Prizm?

On the radiator you have a top hose and a bottom hose. Look at the bottom hose and follow it to where it attaches to the block. Unscrew the two bolts. There is the thermostat.


How do you change a brake light in a 1995 Geo Prizm?

remove the 2 bolts on the outside of the lense then pull the assembly out.