I'd like to add one additional piece of info for anyone who may experience the same thing I did after replacing the headlight bulbs in my 95 Grand Cherokee and reconnecting the battery leads, the security system on the car would not allow me to start the car, and the headlights continued to flash. It was necessary for me to reset the Security System by inserting the key in the drivers door and turning it: left - right - left - right. After that it worked perfectly.
there is a bezel piece going around the headlight. you must remove this bezel (sometimes you have to remove the turn signal light as well) and you will see a metal ring that holds the light in place. be careful as there are two sets of screws. one set adjusts the light and the other removes the ring. drop the ring down and remove the light. installation is the opposite of removal.
hope this is right. that's how it's done on a '94.
On my 95 GC you just grab the headlight lens housing and pull it out. It has two plastic pieces that snap onto two studs that hold lens housing into place. Once you get it out you unscrew a plastic nut and twist and remove the headlight bulb. Then reverse the process to put it back.
I have a 96 Jeep. You just unplug the wire to the back of the headlight. Grab the headlight and pull. There are three snaps two on the bottom and one on the top. I used a little grease on the new snaps. Clean socket and push head light back into place making sure all three snap into place. It took me 15 minutes to complete the drivers side. You have to take the Battery out to get the other wire off the head light on the passanger side. I did not have to use any wrenches to complete this job.
Ok, My wife has a 95 GC that used to be my Dads.
Unplug the wire from the back of the bulb. Locate the light colored ring that is around the bulb base (aprox 2.5" dia.) Rotate that ring until you can pull it off to the rear. Wiggle/rotate the base of the bulb and it will work its way out of the back of the headlight housing.
Reverse process to install new bulb.
Same procedure for Pass side, but start by removing the battery (I have heard you have to leave them disconnected for 10-15 minutes for the computer to fully reset before you reattach it)
Just did this 10 minutes ago
All of the answers above are Correct for 94-98 Jeep Grand Cherokee, Some have the bezel, others do not. Honestly you do not have to unscrew those shafts, it is a snap-on ball on the end of the screw adjustment shaft that connects to the plastic retainer on the Light Housing, 2 or 3 connectors depending on the model. Try not to break the housing, but it will come off with a strong tug or pry with a bar, first one side then the other. If you are just chamging the bulb then the above is also correct about untwisting the ring collar and removing the bulb, from the rear, (inside the engine compartment); remember to reinstall the ring onto the bulb and to not touch the glass bulb.
How do I change a headlight bulb on a 1998 jeep grand cherokee?
I'm trying to replace the headlight assembly for a 2000 Jeep Grand Cherokee Lerado. What bolts or screws do I remove
hey you have get a 7mm screw driver or a socket and unbolt that, it is right above the headlight and then pull the headlight right out. It is in ur manual is this does not help. Mike
To replace a turn signal on a 1994 Jeep Grand Cherokee prop the hood open. Locate the headlight housing and the turn signal will be located next to it. Find the bulb and remove it from the housing. Replace the bulb.
under the right front headlight
behind the passenger side headlight
The piece that a headlight assembly snaps into on a Jeep Grand Cherokee is called a headlight collar. It is also called a headlight assembly.
The lens can not be replaced alone, you have to replace the whole head lamp assembly
Under the bumper cover, under the passengerside headlight.
You have to remove the right headlight assembly, the relay is located underneath the plastic housing below the headlight You can cut a small hole in the housing to gain access to the relay
Autozone.com has a listing for the headlight for a 96 Grand Cherokee, price listed is $95.99 u.s.
right side of car, under the headlight assembly. accessible from under the car.
The following site discusses all lights in the Jeep Grand Cherokee from the WJ model years (1999-2004, inclusive) and includes pictures and diagrams on how to access them so that bulb changes can be made: http://www.wjjeeps.com/lamps/headlamps.htm#LAMPREM
How do I replace water pump on 2004 jeep grand Cherokee
There are bolts surrounding the headlamp. remove these and the wires.
where is the headlight relay
where is the security system located on a 1996 jeep grand Cherokee
for a 1994 Grand Caravan (probably like the 1995) see: How do you replace the headlight assembly located on a 1994 Dodge Caravan? for a 1994 Grand Caravan (probably like the 1995) see: How do you replace the headlight assembly located on a 1994 Dodge Caravan?
The head light is a sealed unit. The outer sense is not removable.
To replace a headlight in a 2006 Suzuki Grand Vitara first open the hood. Prop it safety up and locate the headlight housing. Remove the bulb from the housing and replace the unit.
Jeep grand Cherokees are normally more $ than regular Cherokees, the grand Cherokee was originally made to replace the Cherokee
Werw Is the Evap Canistor located on a 2003 Jeep Grand Cherokee
where is a neutral safety switch located on a jeep grand Cherokee
The relay has probably failed. It is located under the passenger headlight, under the bumper cover.