Get a manual on your car and it will have pictures and everything. Some parts stores have them
Also they didn't make Corsica's after 1996.
Remove the center console remove the floor vent remove the heater core cover the heater core is right under the climate control unit remove the two screws that hold the heater core in place, open the hood and remove the heater hose from the heater core lines, now go inside and pull out the old heater core you don't have to remove the whole dash just the front of it
Yes, just connect the two heater hoses together.
Sounds like your heater core is leaking. Does the fluid look/smell like antifreeze? if so, time for a new heater core.
Fuse- Blower Motor- Wiring- Selector switch fail- i8f you still have heat to the heater core, if the heater core is cold, and the mottr is still hot... change the thermostat
Corsica Joe was born on 1920-01-17.
If a 2001 VW Beetle does not have hot air coming from the heater there is a problem with the vehicles heating system. The heater core is malfunctioning and will need to be replaced.
You will need to remove the dash and it should be somewhere under
you could have an air pocket in your core. the speakers check fuse.
Your heater core could be plugged. I've had it happen to a 98 and an 01 S10 pickup. I flushed the core both directions and it heats like crazy now.
Armored Core V was created on 2012-01-26.
The Heater core is difficult to replace on the RAM since it is buried in the plenum box. The box has a convenient door panel that you can open to remove and replace the core. The catch is that the convenient door is on the back of the box and you have to remove the heater box to get to it. This involves removing the steering wheel, steering column, complete dash panel, evacuating the AC, draining the radiator, and finally removing the heater box. Once you have the box out(8-12hrs), the core is simple to replace. You want to be sure that the core is the problem before you undertake this process. If there is a strong smell of antifreeze in the cab or a puddle of coolant on the passenger side floor, the diagnosis is easy. Check that the radiator is full, not the overflow tank, the radiator. On a cold engine you can remove the radiator cap and check the level. It should be full. If there is air in the system it will affect cab heating and engine cooling. Another good check is to feel the two heater hoses going into the firewall from a cold start. The hoses should warm up at about the same rate and get uncomfortably hot-close to radiator temperature. If the core appears to be OK, the next concern is with the blend doors that divert air through the heater core. This is a common failure on the RAM. Check heatertreater.net for an explanation of the operation of the system and a fix for the common problems. The RAM has four different DC servo motor controlled air flow doors that are susceptible to failure and all of these need to be checked by either observing the symptoms of failure or reading the codes. The problems are easy to fix with the HeaterTreater kits, but the OEM dealer fix requires removing the plenum box as described above. It is a costly repair if you take it back to the dealer and are not under warranty.
The Heater core is difficult to replace on the RAM since it is buried in the plenum box. The box has a convenient door panel that you can open to remove and replace the core. The catch is that the convenient door is on the back of the box and you have to remove the heater box to get to it. This involves removing the steering wheel, steering column, complete dash panel, evacuating the AC, draining the radiator, and finally removing the heater box. Once you have the box out(8-12hrs), the core is simple to replace. You want to be sure that the core is the problem before you undertake this process. If there is a strong smell of antifreeze in the cab or a puddle of coolant on the passenger side floor, the diagnosis is easy. Check that the radiator is full, not the overflow tank, the radiator. On a cold engine you can remove the radiator cap and check the level. It should be full. If there is air in the system it will affect cab heating and engine cooling. Another good check is to feel the two heater hoses going into the firewall from a cold start. The hoses should warm up at about the same rate and get uncomfortably hot-close to radiator temperature. If the core appears to be OK, the next concern is with the blend doors that divert air through the heater core. This is a common failure on the RAM. Check heatertreater.net for an explanation of the operation of the system and a fix for the common problems. The RAM has four different DC servo motor controlled air flow doors that are susceptible to failure and all of these need to be checked by either observing the symptoms of failure or reading the codes. The problems are easy to fix with the HeaterTreater kits, but the OEM dealer fix requires removing the plenum box as described above. It is a costly repair if you take it back to the dealer and are not under warranty.
A/C's don't have water in them, but your heater core could; if it is broken, this would require immediate attention as coolant fumes can harm nervous systems,liver, and kidneys in our bodies even if you can't smell them, rather quickly!
Use a 5.5 mm socket to remove the three bolts in the panel under the dash, then remove the 2 bolts out of the blower resistor. Disconnect the wire connector, then remove the resistor.
easiest way to replace anything is to get someone else to do it
singal relay where 2001 Taurus
ON the coolant resevoir, look for the hose that runs to a tubular metal connection, it is a smaller hose at the top, make sure coolant flows out when the car is started, willing to bet it is blocked from the point where it connects to the heater core unit. I had the same problem. car works fine now
The Gateway LX6810-01 Intel Core 2 Quad Q8200 2.33GHz Desktop comes with a NVIDIA GeForce GT120 PCI Express Video Card graphics card.
Not exactly sure what a "heater lock out switch" is... Check out the "Related Questions" below for a couple of good questions/answer that might help guide you to more specific details on your problem.
i got mine done for $160
just found out today-$460!
i have a 2002 f250 and mine is inside bumber down around fog light area.
How is it failing? leak, plugged etc.? There is a technical service bullitin regarding this : # 01-15-6. Essentially it has to do with most ford products. There may be a ground problem, or lack of coolant flushes. You can get the complete service bulletin at this address: http://www.alldata.com/recalls/
I just replace rotors and pads on my 01 eclipse gt for $100 canadian. This is the price for the parts only. Labour was extra.