0
its a long process,you need a steering wheel puller, once its off take the hazard button assembly out, take the turn signal loose, pull old ignition out, carefully install new one, and reverse procedure
Wiki User
∙ 16y ago
Wiki User
∙ 19y agoIs it the switch, or the lock that you want to replace?
Wiki User
∙ 8y agoThe switch is located on the left side of the steering column. You have to remove the panel underneath the dash to access it.
There will be two screws holding it on.
Wiki User
∙ 18y agothe ignition switch is located on top of the steering column under the dash, held on with 2 screws
Add your answer:
Earn +20 pts
Why would the starter keep on trying to start the car even though the key isn't turned or even in on a 1993 NA Supra?
replace ignition switch
How do you remove a 1993 mercury tracer ignition switch if you HAVE the ignition key and can turn it to the on position?
you need to push in the hole with 1/8 inch screw driver under the steering column, below your ignition switch. there is a release button in there and it just pulls out once you have that release button pushed it's actually quite easy..
Where can I find a free electrical wiring schematic for the ignition switch of a 1993 dodge B350 5.9L van?
It is important to have a diagram when making electrical changes to a car. A free electrical schematic for this cars ignition switch can be found in the manual, or a person can ask a tech at a shop to print one off.
Where is a ignition module located on a 1993 dodge colt?
where is a ignitionmodule in a dodge colt a 1993
When the ignition key won't turn on a 1993 Ford Escort how do you pull the ignition switch apart to see what's going on?
Place your key in the ignition, and with the back of a screwdriver( Handle end) lightly tap the key and try to turn at the same time in the ignition, .The tumblers or wafers often get stuck and may help them slide into their proper location. The Focus is notorious for this problem. I have used ths method several times and was able to pull my ignition assembly for replacement. Hopes it works for you, did for me.
Replace ignition switch for 1993 Buick century?
Replace ignition switch for 1993 buick century?
How do you replace the ignition switch on your 1993 Chevy K 2500?
Remove the retaining ring at the top of your 1993 Chevrolet K 2500 ignition switch. Slide the ignition switch out and remove the wiring harness. Reverse the process to install the new ignition switch.
How do you remove the Ignition switch assembly on a 1993 Acura Legend?
you have to replace the whole steering column
How do you replace the ignition switch on a 1993 Pontiac Grand Am?
It's really easy the switch is in the steering colume.
How to replace ignition switch on 1993 buick regal?
I believe that the switch is located in the ignition cylinder (which you can get from any auto parts store). Unfortunately you'll need a steering wheel puller and a tilt removal mechanism before you can start with that.
What is the cost to replace the ignition switch on a 1993 Ford Ranger?
It depends on what part of the country you live in. Call a couple of local garages for estimates.
How Do You Replace A Headlight Switch In A 1993 Oldsmobile Cutlass Ciera?
how do you replace the headlight switch on a 1993 cutlas ceria*
Why would the starter keep on trying to start the car even though the key isn't turned or even in on a 1993 NA Supra?
replace ignition switch
How do you replace a 1993 Corvette headlight dimmer switch?
How do I change the dimmer switch on my 1993 corvette?
How do you replace ignition swwitch in 1993 caravan?
you will need security type star screw drivers , remove three screws from bottom of column cover,remove three screws from ignition switch.Replace with new switch.
How do you change the ignition switch on a 93 Nissan quest?
Begin by removing the retaining ring at the top of your 1993 Nissan Quest ignition switch. Slide the ignition barrel out. Remove the wiring harness from the end of the ignition barrel. Reverse the process to install your new ignition switch.
What does it cost to replace the ignition switch on a 1993 subaru legacy?
I had the Suby dealer in Auburn WA fix mine, the unit is held in place with 2 long bolts. The metal brackets are welded together and the electrical connections have to be soldered to the new Ignition switch. Cost-$289 or so.
