answersLogoWhite

0


Best Answer

This is not a hard job. I myself have an 87 Ford and i just did this! dont rip apart your steering wheel! first remove the bolts where the shaft goes through the fire wall! there is like 8! Then pop the hood and there is one bolt on the steering shaft take that off. Next remove the aluminum plate in the shaft the steering wheel should fall, pull in completely off, but before that disconnect the wires that go into the harness(ignition switch). There is a rod that goes into the switch which turns the truck on and the radio and so forth! Take off the 2 bolts holding the switch in! Becareful not to break them. Then put the new switch in adjust it to neutral with the little wire they give you. Be really careful tightening the switch to the shaft. If you snap thosebolts you will have to get a whole new shaft! Then adjust the switch so when you turn the ignition everything works like normal then tighten the switch to the shaft and reverse the steps for reassemble!

User Avatar

Wiki User

โˆ™ 2011-03-24 03:46:23
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How do you replace the ignition switch on 1987 ford f250 non tilt steering wheel?
Write your answer...
Submit
Related questions

How do you change an ignition key switch?

you have to remove the steering wheel. (if it has an airbag, be very careful not to set it off.) if no airbag, just remove the steering wheel, and on the ignition switch there is a bolt that simply screws out. remove the ignition switch, and replace with the new one. line up the bolt holes, and replace bolt. put steering wheel back on, and youre done.


On a 93 Chevy cavalier- do you have to pull steering wheel to replace ignition switch?

yes


How do you install ignition switch 1988 gmc truck?

You need to remove the steering wheel first with a puller. There is a latch you can trip with a small screwdriver that will let the ignition switch slide out. Simply replace the switch and put the steering wheel back on.


Why is it NECESSARY to remove the steering wheel to replace the ignition switch on a 1994 Ford Explorer?

I was under the impression the switch was on the steering column about 18 inches from the floor. The lock assy is under the steering wheel.


How do you replace the ignition switch in a 1990 Chevrolet Corsica with tilt wheel?

The switch is on the steering column about 18 inches from the floor. Simply take 2 screws holding it on and replace it.The locck cylinder is under the steering wheel.


How do you change ignition switch on 1998 Buick century Do you have to remove the steering wheel?

do I remove steering wheel to change out ignition


How do you replace the ignition switch in 1996 S10 Chevy pickup?

Remove cowling from under the steering wheel, remove the two nuts holding the wheel coloum. Drop the steering coloum. Ignition switch is about a foot down on the left side. Unhook the wires remove switch replace. P.S. Unhook battery cables high voltage in ignition system.


How do you change the ignition switch in a 1987 Ford Bronco 2?

Remove the airbag and steering wheel, remove the torx screws from the steering housing and remove the housing, remove the screws from the signal and wiper switch, and remove the screws above the ignition switch and remove the switch. Replace the switch and replace everything in reverse.Ê


How do you replace the ignition switch on a 94 Pontiac Sunbird?

i had to replace the ignition switch on my 94 sunbird 2 weeks ago...mine has no airbag, and hopefully for this repair yours doesnt either. you have to remove the steering wheel. on the ignition switch there is a bolt that simply screws out. i dont think i had to remove anything else...maybe the turn signal switch, but nothing major. remove the ignition switch, and replace with the new one. line up the bolt holes, and replace bolt. put steering wheel back on, and youre done.


Where is the ignition switch on a Mazda pickup?

by the steering wheel


How do you remove a key that is stuck from the ignition of a 1996 Dodge Caravan Steering wheel is not locked and cannot start the vehicle?

You can't, you have to replace the ignition switch


How do you replace ignition switch on 1984 Chevy half ton non-tilt wheel?

the ignition switch is located on top of the steering column under the dash, held on with 2 screws


How do you replace the turn signal switch located on a 1990 Ford Bronco?

You have to take apart the steering column, remove the steering wheel, remove the ignition switch, and it's a pain in the butt.


How do you replace a starter switch in a 1987 Chrysler LeBaron Town and Country Turbo with a tilt wheel?

There is a solonoid on the starter and the ignition switch is on the steering column.


Where is the ignition switch in a ford expedition xlt v8?

The ignition switch is located on the steering column right side, just below the steering wheel.


How do you replace ignition switch on 97 gmc jimmy?

Pull your steering colum apart along with steering wheel and dash plastic, ignition swith is next to the key tumbler. Swap the parts.


How do you replace an ignition switch in a 1992 cavalier?

First remove the steering wheel, remove the torx screws and remove the house, remove the signal switch and the wiper switch, remove the torx screws and?æremove the ignition switch. Put in the new switch and replace everything in reverse.?æ


Why won't ignition switch turn?

The Steering Wheel lock is jammed! Gently wiggle the steering wheel back and forth as you try to turn the ignition key.


How to replace the ignition switch?

remove the steering wheel. unbolt the collar that holds the steering column underneath the dash. that plastic box halfway down the column with all of those wires hanging out of it is your ignition.


How do you replace an ignition switch 1984 ford ranger?

take the steering wheel off and take the ignition lead off and then you buy a new ignition with new key or vis versa


How do you remove and replace the ignition switch in a 93 LeBaron?

to replace the switch u will need the key to the old ignition switch. its as simple as getting a t15 bits to take off the steering colum and unscrewing the switch i think the bit size is t25 and you need a special bit with a hole in the center of it. you take off the steering wheel column covers.


How do you replace the turn signal switch on a 2001 Yukon?

You need to remove the steering wheel. The switch is located below the steering wheel.


Do you have to go through the steering column to replace an ignition module?

Are you talking about the electronic ignition module or the ignition switch? The ignition module sits in the engine compartment and is part of the ignition system (coil, spark plugs, etc). The answer is no if this about what you're referring. The answer for the ignition switch will depend on the vehicle you have. Some, like late model Fords, you don't. Push in the retaining pin and the ignition switch comes right out (you still need a key though). Others you need to take off the steering wheel to replace the switch.


Why won't my 1988 325i BMW ignition switch won't turn?

Maybe your steering wheel it's keeping the ignition cylinder to turn, so move the steering wheel and at the same time try to turn the key. Maybe you need to replace the ignition cylinder key lock


Can you drop the steering column without taking off the steering wheel to replace ignition switch?

Yes. Just take the U clamp off the bottom of the steering column and it will drop down so you don't need to take off the steering wheel.