answersLogoWhite

Top Answer
User Avatar
Wiki User
Answered
2011-09-12 21:00:30
2011-09-12 21:00:30

With mucho effort, that's how. The sensor is behind the intake manifold, throttle body ect, all of which must be removed. Labor alone will be 5-6 hundred , knock sensor another 150 or so. Good luck.

001
๐Ÿฆƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


I AM GETTING A OBD CODE ERROR FOR MY 2000 NISSAN QUEST , PO141 AND PO325 ??? HOW DO I FIX IT..


how many gaskets and which ones are needed when you replace the knock sensor on a Nissan frontier w/a 3.3l v6 engine?


The knock sensor for most Nissan V6 engines is located directly under the intake manifold. So to replace it, you have to remove the intake manifold. Good Luck.


If just the knock sensor need to be replaced. I would say no more than $150.00


The knock sensor on a 1998 Nissan Quest is also located under intake manifold and yes alot of work but can be done in a day. 120 dollar part and 500 labor at garage but for u at home mechanics just a simple side project.



the Knock sensor is located behind the Harmonic balancer pulley. on the bottom sidethe sensor is $95.00 remove the lock down screw unplug and replace


the knock sensor is located under the intake manifold, with a flash light you can see it however you have to remove the intake manifold to replace the knock sensor , also you will need to replace the intake gasket set as well!


It is behind the intake manifold on the left side of the engine. It will take almost 6 hours to replace this cheesy part ($120) and cost about $500 in labor alone.



The knock sensor is located below the intake manifold


The knock sensor is located below the intake manifold


The knock sensor on Nissan 300ZX non-turbo from 1990 thru 1996 is located below the lower intake manifold on the rear of the engine block. To replace the knock sensor the upper and lower intake manifolds need to be removed. It is always best to replace the knock sensor with a new one considering its major dissasembly.


how do I disconnect the Electrical connection on knock sensor


You can find a 1996 Nissan Pathfinder knock sensor picture in most auto repair manuals. Most Nissan dealerships repair centers will provide you with a picture of the sensor.


not easy, it's under intake manifold between the heads. Have to take off plenum, water bypass pipes. it's the only electrical wire on the top of the block!


how you can remove the knock sensor from a 1996 Nissan pathfinder i need a picture


on a 2001, with the 3.3, the knock sensor is under the water crossover pipes, which are under the intake manifold. Pain to change. Take off plenum, intake manifold and there it is, on top of the block between the heads.


where is the knock located on 2001 nissan altima 2.4


how to replace a knock sensor on a 2000 Chevy 6.0 step by step


how to replace a knock sensor on a 2002 hyundai elantra


The knock sensor is located below the intake manifold


Th knock sensor on a 2002 Nissan Xterra 3.3 is located on the top of the engine. It is mounted under the engine intake.


Disconnect the wire from the sensor, use an open ended adjustable wrench to unscrew it. take a new sensor and screw it in. on a different model (if not a standard sensor) there is a nut and bolt holding it in, use the steps above to replace it


The 4.8, 5.3 and the 6.0 GM engines require removing the intake manifold to replace a knock sensor.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.