Chevy Tahoe
1995-1999 Dodge & Plymouth Neons
Mazda 626
DIY Projects

How do you replace the license plate lights on a Mazda 626?


Top Answer
User Avatar
Wiki User
2015-07-15 21:13:02
2015-07-15 21:13:02

Open up your trunk and look up above the license plate. It is held in by screws. undo the screws adn unit drops down.

User Avatar

Related Questions

How do you replace the license plate lights on a 2000 celica?

How do you change the liscence plate light fuse

You need to unscrew the whole cover panel for license plate.

to wire the license plate lights you must have lights and wire them to the scooter.

No, the license plate light is wired in with the rear tail lights, not the brake lights.

there should be 2 screws above license plate, take the off piece pops off and replace lights

Remove the plastic cover on the outside and just pull the bulb out

The license plate lights are not in a separate fuce by it seft. They are the same as your side marker lights. So, check if your side marker lights are working and if they are them is a bad license plate light bulb.

yes 2002 Ford Focus do have 2 lights on license plate

It is the same fuse that controls the tail lights. It is at the top of the fuse box 2nd from the left. 15amp fuse.

Open the trunk and look for the wires that connect to the license plate lights. You should see a plastic piece that hooks into a socket. Simply grab the plastic piece and turn and the lights should come right out. The lights may be behind a paneling.

Raise the trunk will see the lights on each side of the license plate...use Phillips screw driver to remove and replace bulb. Just did this takes about 2 minutes.

Open the trunk. Turn the socket counterclockwise and remove. Then gently pull out the light bulb. Place the new bulb in the socket and replace the socket into the lens by turning clockwise. Replacement light bulb #3652.

That would be the lights that illuminate the rear license plate.

You need to remove the liner on the trunk lid. That will give you access to the license plate lights housing. Remove the sockets by twisting 1/4 turn and replace bulbs. Size for bulbs are 2825

there are two spots above the license plate where the lights go on each one there should be a spot where you can push the cover in and then just pull out at an angle

The license plate lights are located just above the license plate. Open the tail gate part way to make removal easier (unless you enjoy squatting). Remove the Phillips screws and replace the affected bulb.

1. Open the trunk and reach behind/above the license plate to find the backside of the two licence plate lights. 2. Turn them each about an 1/8 of a turn to remove the light and an associated plastic housing. Remove the lights from the plastic housings (this was difficult ... apparently they get stuck with age). Replace the old lights with new ones purchased at an auto parts store. 3. Put the plastic housings with new lights back into from where they came.

05+ Honda Odyssey license plate lights. Pop out the license plate lights in the rear. There are two of them. Use a very thin flathead screw driver and pop out the sides of the inner clear light assembly. They are on the sides. Once that is done, remove the light bulb and replace with a new bulb. Pop in the clear light assembly cover. Turn on lights to see if the bulb is working and it is is then you're done. Approximately 10-15 minutes total.

how to replace the license plate bulb on a 2004 Honda cr-v

Tail lights. Brake lights. Backup lights. Signal lights. License plate lights.

how do you replace a honda crv licence plate bulb on a 2004

how do u change the license plate light on a 2005 sienna

There are two (2) lights directly above the license plate. Each light has two (2) screws. Remove these screws and the covers. Lights pop out with little effort. Replace bad bulbs with size 194 lights. These are approx $2 at walmart or an auto parts store. Once bulbs are replaced, reattach covers with the screws and you should be good to go.

Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.