You have to remove the bumper in order to access the whole headlight assembly...sucks XD
Open the hood, take off the bumper (the placement consists of a few clips) and you have access to the headlight bolts. Unscrew those and you will remove the headlight.
remove headlight frame you can see it then
By removing the locks that hold the headlight assembly in place you can wiggle the headlight assembly out to gain access to the headlight bulbs for replacement.
Open the hood, remove the two locks that hold the headlight assembly in place, with the two locks removed you can wiggle the headlight assembly out and gain access to the back side of the assembly to remove and replace the headlight bulb.
Remove the entire headlight assembly to gain access to the bulbs.
for the passenger side light, you need to remove the plastic cover above the headlight. then pull the two black clip up (using pliers) then wiggle the entire healight fixture out. this gives you access to the bulb.
Remove the headlight retaining bolts. The retaining bolts can be access through the engine compartment. Remove the wiring harness. Reverse the process to install the new headlight.
The bulb is replaced from the engine compartment. The driver side is much easier to replace than the passenger side because you can pull the battery out. Once you have access to the area the headlight wire harness releases from the headlight assemble by lifting the plastic hook that latches to a nob on the light bulb assembly. Since it's plastic it can break very easily. Once you have released the headlight wire assembly the bulb is held in by a plastic collar that turns counter clockwise about 1/4 to 1/2 turn. It is difficult to get a good grip on this piece and that is the hardest part of the job. When the collar is off the headlight bulb just pulls straight out. You then reverse the process to put the new bulb in. Ray
Gain access to the rear of the headlight housing. Remove the weatherproof rubber protective boot and remove the headlight bulb socket. Replace bulb and re-install in reverse order.
Remove tire & inner liner to gain access to head light assembly
Remove the headlight assembly and you will have access to the parking light bulb.
It is under headlight on the passenger side and behind the foglight. You either have to access it from the fenderwell or or by removing the headlight (easier method). It is held on a bracket with one bolt.
In the front of the passenger side fender, The easiest way to access them is to remove the headlight assembly.
It looks as if I'll have to crawl under the front of the car to access the bulb to replace it.
To replace the high-beam headlight bulb on a Volkswagen Golf, first the back cover of the headlight compartment must be removed. This allows access to clips that hold the bulbs in place; from there, the bulbs can be changed.
I some cases. They can not if there are parts to be removed to gain access to the light. They can not be outside for very long.
It is on the passenger side of the car under the hood, mounted on the finder. It is under the battery box behind the Right headlight. The battery and the battery box must be removed to access it to work on it or replace it.
Not an easy task since you have to remove the Front Bumper Cover to get access to it. Once that's done, remove the electrical connectors, the screws and the Headlight Assembly.
This is for the passenger side headlight assembly. The driver's side is has a plastic cover that must be removed first, so the setup underneath may or may not be different... Remove the three 10mm hex bolts from the top of the headlight assembly holding it to the vehicle. The middle bolt has a bracket connecting it to the vehicle by a fourth hex bolt, which you may need to loosen to move the bracket out of the way. Pull the headlight assembly forward until you can access the bulbs. They can be removed from the assembly by a quarter turn, then unclip the faulty bulb and replace.
2005 Honda Accord headlight bulb replacement: Purchase the correct replacement headlight bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement bulb information. Then consult your owner's manual for the headlight bulb replacement procedure. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions and illustrations. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional). The owners manual will be of no help in detailing how to replace the bulb. You gain access to the driver side headlight bulbs through the wheel well. Removing the tire/wheel helps considerably. You access the passenger side bulbs by removing the battery.
Remove headlight assembly to access bulb/socket.
If you remove the headlight assembly you will have access to the turn signal bulb.
replace blown bulb then access body control module with a scan tool and clear headlight fault code , the headlight should now work
Passenger side or driver side? BClear. The low beam is built into the same bulb as the high beam. Just pull the bulb out from behind the housing under the hood and replace it. If the low beam doesnt work you have to replace the whole bulb. They're not very expensive.