answersLogoWhite

0


Best Answer
Copy

you must remove the transmission, two bolts hold the slave on the front of the trans, and be sure to disconnect the hydrolic line ( no easy task)

The line is removed by pushing out the little pin near the end of the slave using a punch(hard part described above) once the pin is removed the line will slide off the slave.

**watch for an oring it will fall out and you will lose it .. DONT u need it. the install is the reverse acccpt your need to bleed the slave the same way you do brakes.

This is not correct. You do not have to remove the tranny on 94 and 95 models. You only have to remove the brace from engine to transmission. Then after that, everything else is the same.

User Avatar

Wiki User

โˆ™ 2015-07-15 19:06:55
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you replace the slave cylinder on 1997 Chevrolet S10?
Write your answer...
Submit

Related Questions

Do you have to pull out the transmission to get to the slave cylinder in a 1997 Chevrolet Cavalier?

No


How do you replace the clutch cylinder slave in a 1997 Chevrolet S10 pick up?

Replacing the clutch slave cylinder requires removing the transmission assembly. I would recommend purchasing a shop repair manual for that vehicle if you intend on DIY.


Clutch fluid leaking on the ground on a 1997 Hyundai?

your slave cylinder is leaking,need to replace.


Where is the slave cylinder on a 1997 S-10 with standard transmission?

On my 1998, the slave cylinder is located inside the bell housing - a very stupid place for it IMO. If you are replacing the slave cylinder, it might be a good time to replace the clutch too.


How do you replace the clutch slave cylinder on a 1997 Isuzu Rodeo?

take the cap off and roll another rodeo under it


Where is slave cylinder on 1997 Isuzu hombre?

The slave cylinder is on the input shaft of the transmission at the throw out bearing. The transmission will have to be removed to change it.


Where is the clutch slave cylinder on a 1997 ford ranger?

The clutch slave cylinder for a hydraulic clutch is inside the manual transmission bellhousing


What is the labor and materials cost to replace a slave cylinder in a 1997 Saturn SL2?

Its best to buy the slave and master cylinder prebled from the dealer. Its $140 or so but it saves alot of hassle if you dont bleed it right. Labor...Each side twists in to there perspective locations and then 2 bolts hold on the slave cylinder to the tranny.


Where is the slave cylinder located on a 1997 ford ranger xlt?

The slave cylinder for your hydraulic clutch is located inside the transmission bell housing


Where is the slave cylinder on a 1997 Ford Ranger xlt?

The slave cylinder for a hydraulic clutch on a Ford Ranger is inside the manual transmission bellhousing


Where is the number two cylinder on a 1997 Chevrolet 350?

It is the forward-most cylinder on the passenger side of the engine.


How many spark plugs does a 1997 Chevrolet s10 have?

One for each cylinder, six in a six cylinder, four in a four cylinder.


How do you replace the hydraulic clutch line on a 1997 Chevrolet S10 pickup?

how do you replace hydraulic line on a 1997 s-10


Where is the slave cylinder on a 1997 gmc sierra 1500?

slave cylinder is located on the starter passenger side of vehicle. it should be attached to the transmission by 2 nuts.


Why is do you have to put clutch fluid in 3 times a day on my 1997 cavalier?

Leak in master cylinder? Leak in slave cylinder? Leak in tubing from master to slave cylinders?


Can you replace your 2000 Camry CE 4-cylinder engine with a 1997 Camry engine?

Can you replace your 2000 Camry CE 4-cylinder engine with a 1997 Camry engine?"


What is the oil capacity of a 1997 Chevrolet 3.8 Liter six cylinder engine?

4.5 liters


Should you change the master or slave cylinder in a 1997 4 cly Accord that has little clutch pedal resistance and won't disengage clutch when the fluid was low and bleeding got all fluid at slave?

It's the slave cylinder.


How do you replace the clutch slave cylinder on a 1997 Pontiac Sunfire?

you have to remove the tranny and clutch! 4-6 hours depending on who and where you get it done and the tools they have most people charge about $70/$80/hr


Do you have to remove transmission to replace slave cylinder on 5.7 1997 5 speed Chevy truck?

YES. It will have 3 bolts that hold it in place in the bell housing. Must remove transmission to service.


How do you replace 1997 Chevrolet Tahoe ball joint?

Do you need any special tools.


How do you replace an ignition cylinder in a 1997 Mitsubishi mirage?

This website never has a good answer!!


Where is the cluch caliber on a 1997 Nissan king cab pick-up located?

Do you mean clutch slave cylinder,if so ,its bolted on side of transmission,with rubber cover,if leaking,replace and bleed.


How do you remove the hydraulic line from the slave cylinder on a 1997 Chevrolet s10?

pull the cotter pin out with with a pair of pliers and and remove the the little metal sleeve the cotter pin was in. you can use a small nail to achieve this. slide the hydraulic line straight out.


What size gas tank does a 1997 Chevrolet s10 2.2litre 4-cylinder 5speed have?

18 gallons