. There may be minor differences in the 96-99 years, this is specifically for a '95. Hopefully it's close. 1: Open hood and remove plastic heat/noise shield from top of motor (4 plastic nuts) 2: On the passenger side of the engine, near the front valve cover, you will see a small box labeled "Battery +" in red letters. Pop that cover. This is the lead to the starter. If you don't want to have to pull the backseat for the battery just remove the nut and pull this wire. 3: Remove the silencer and intake tube from the airbox (the box itself can remain). 4: Label and remove the 4 front spark plug wires. I lay them down on the hood and hold them with the wiper. 5: Disconnect the TPS sensor (side of TB, away from passenger compartment) 6: On the '95, disconnect wiring to the Idle Air Motor (96-99 have it in the TB, different wire). 7: Disconnect the wiring look for the Fuel Injectors, it's down and slightly rear of the TB itself, large round plug. 8: Disconnect the fuel lines at the firewall. You can leave them on the fuel rail. 9: Undo coolant line from underneath the TB (spring clamp) Pull off and let drain out while you work. 10: Remove all vacuum lines from TB (one large on the side, 2 small up top, 1 or 2 more i forget). 11: Now is a good time to check the vacuum port on top of the TB. It just unclips. Mine had several cracks in it. 12: Remove EGR pipe from side of TB. It bends out of your way, but go easy on it. 13: NOW check to make sure all your vacuum lines and wiring it out of the way and not going to fight you as you move the intake out of the way. 14: If you havn't already, remove the 4 studs that are the supports for both the top cover, and the hold downs for the fuel rail. 15: Remove bolts for the intake. 10mm. I believe there is 4 of them per side. I know if you have had the fuel recall done that they re-locate the FPR to the front. Right over a bolt. Just use a short open-end wrench and you'll be fine. They're not tight. 16: Some of the bolts will come out, some may not. I had 2 or 3 that wouldn't come. That's fine just make sure you have them completely backed out. 17: This part is probably easiest with two people, but one should be able do it with not to much trouble. Grab the TB mouth and the end of the intake (where the pressure-relief door is) and lift straight up. The whole unit should come up. 18: Rotate the whole thing counter-clockwise. That's with the TB facing the passenger compartment and the pressure-door facing the front. 19: If you're like me, there will be tons of leaves and stuff down there, take this opportunity to vacuum it out. Also if you feel compelled, you could clean all the intake ports too. Take rags or paper towels or tape or SOMETHING and put it over the intake ports, don't want anything down there. 20: Remove the starter with the wires still attached, this is why you removed that B+ lead before hand, RIIIGHT? It's two 10mm bolts, plainly obvious. There isn't any hidden or anything. 21: Pull the starter back and up, and rest it on the valve cover. Use a 14mm socket for the main lead and a 8mm for the trigger lead. 22: Put the wires on the new starter first, then place it back into the car. 23: Installation is reverse of removal! Also, check to see how your intake gaskets are. Mine were OK, but it might be a good idea to replace them. I know there was a marking on manifold saying it was replaced at 14k miles. I hope this helps anyone, i know the dealer will want at least $500 to do this job, plus the starter. I priced a 2 year guarantee starter at $235, and the labor took me about 2 hours.
where are the fuel injectors in a 1997 oldsmobile aurora
remove and replace water pump in 1997 Oldsmobile aurora
Are there any major differances between a 1996 and 1997 Oldsmobile Aurora
Most of the relays for the 1997 Oldsmobile Aurora are under the back seat on the drivers side.
Where is the speed sensor located on a 1997 Oldsmobile Aurora
Remove the positive cable from your 1997 Oldsmobile battery. Remove the starter cables from the front of the starter. Remove the starter retaining bolts. Reverse the process to install the new starter.
How do you replace starter in 1997 BMW 740il??
pump is in fuel tank. accessible through trunk. if replacing, also replace fuel filter.
the starter is located under the intake manifold The large power cable on the battery most always goes to the starter which is on the bottom of the engine near the transmission area and is most likely below the intake manifold.
The Owner's Manual and Operating Instruction for the 1997 Oldsmobile Aurora is offered on Manual Owl as a PDF. The website provides product manuals free.
1 in each cylinder...........
The 1997 Oldsmobile Aurora flasher fuse can be found in the fuse box. The fuse box is in the engine compartment. The location of the fuse will be listed on the inside cover of the fuse box.
The 1997 Oldsmobile starter relay switch can be found in the fuse box. The starter relay switch will be at the top of the third column.
How does one remove and replace the starter in the 1997 Bravada??
Takes dextron 3
The body control module, on your 1997 Oldsmobile, is located on the rear suspension. The module is mounted on the passenger side of the rear axle.
7.5 quarts of oil
as much as you want or whatever the tire recommends
most likely 14 to 16 gallons
Where is the starter on a 1997 Honda Civic?
The starter relay is inside the starter. You will need to replace the starter.
How do you replace a starter in a 1997 F-350 Turbo Pickup?
it can cost any were from 200 to 450 to replace the starter.
bottom pulley. at end of crank.