answersLogoWhite

0


Best Answer
Copy

Follow the upper radiator hose down to the engine. It is attachedto the thermostat housing . Therewill be two bolts attaching the housing to the engine. Remove thesebolts, and with a little effort (prying),the housing will come off. Therewill probably be brackets, wires,or other items which will have Tobe removed in order to get to the bolts.Installation is just the reverse, and be careful you don't get the bolts tootight.

User Avatar

Wiki User

โˆ™ 2011-09-12 21:04:43
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you replace the thermostat located on a 1993 Mercury Villager?
Write your answer...
Submit

Related Questions

How do you replace a Mercury Villager thermostat?

This can be a tricky process. Unless you have some experience with vehicles, it might be best to leave to the professionals.


Where is the thermostat located and how do you replace it located on a 1998 Mercury Villager?

Passenger side (front of the motor) in the middle. Just above the water pump. Must remove cover and harmonic balancer to install. Very difficult.


How do you replace the thermostat located on a 1994 Mercury Cougar?

What is the motor size? Run1


Where is the heater valve located on a 99 Mercury Villager and how do you replace it?

On the firewall behind the intake. PITA to get to or even see for that matter


How do you Replace crankshaft on 1999 mercury villager?

You don't, you replace or rebuild the engine.


How do you replace ignition fuse on a 1995 Mercury Villager?

To replace the ignition fuse on a 1995 Mercury Villager, use a fuse puller to remove the appropriate fuse. Then replace broken fuse with one of the same amperage.


Where is the thermostat located in a 1999 Toyota Camry and how do you replace it?

where is the thermostat located in a 1999 Toyota Camry located and how do you replace it.


How do I get the transmission on a 1994 Mercury Villager Van out of fail safety mode?

Replace the transmission computer. Located under the center console.


How do you replace an oil sending sensor on a 96 Mercury Villager where is it?

The oil pressure sending unit is located right above the oil filter.


Where is a water pump located on a 1995 Mercury Villager?

The water pump just below the top timing belt cover, right side of the vehicle. Not much space to work in, but I just replaced one while I was replacing the timing belt. To the left of the water pump is the thermostat housing; where your engines thermostat is located. I also replace the thermostat while I had the timing covers (top & bottom) removed. Rick


How do you replace the thermostat located on a Oldsmobile Custom Cruiser?

remove old thermostat and replace with new thermostat and gasket


How do you replace the thermostat located on a 1994 Pontiac Bonneville?

Where is the thermostat


How do you replace the odometer cable on 1998 Mercury Villager?

You don't as it does not have a cable. You replace the speed sensor instead.


How do you replace dash lights 1994 mercury villager van?

To replace lamps the cluster must be removed.


How do you replace the moniford on mercury villager?

I would like to answer that but I don't know what a "moniford" is.


How do you replace the thermostat located on a 1985 Ford Bronco II what side of the thermostat go?

how to replace a thermostat on a bronco 198511


How do you replace the thermostat located on a Mazda truck?

how do replace the thermostat on a 1999 mazda b2500 truck?


How do you replace the thermostat located on a 1991 Mercury Tracer?

On your 1991 MERCURY TRACER, the THERMOSTAT is: UNDER HOOD, DRIVER SIDE, UPPER ENGINE AREA, ENGINE END OF UPPER RADIATOR HOSE, MOUNTED IN COOLANT OUTLET HOUSING.


Where is the thermostat located and how do you replace it 1992 Toyota Camry?

Where is the thermostat located and how do you replace it on 1992 toyota camry 4 cylinder ingine


Where is the thermostat located on a 1998 Camry?

Thermostat is located inside water outlet. You have remove the outlet if you want to replace the thermostat.


How do you replace the fuel pump on a 1998 mercury villager?

The fuel pump is in the tank and the tank must be removed to replace it.


Mercury villager idler pulley frozen?

If the idler pulley is frozen, it is high time to replace the timing belt and the idler. And while that job is being done, consider replacing the water pump and thermostat.


How do you replace the rear brakes and are special tools needed for a 1997 Mercury Villager?

The brakes on the Villager are as straight forward as the brakes on a 1965 Mercury. Only normal brake tools are required.


When do you replace a timing chain on a 1993 Mercury Villager?

The engine in the Mercury Villager does not use a timing chain, it uses a timing belt. The recommended belt replacement interval is 105,000 miles.


How many labor hours to replace a water pump on a mercury villager?

3.5 HOURS