Auto Parts and Repairs
Windshields and Wipers
Pontiac Transport
Chevy Blazer S-10

How do you replace the wiper motor on a 1996 Pontiac Transport?

464748

Top Answer
User Avatar
Wiki User
2011-04-24 16:17:29
2011-04-24 16:17:29

It is a simple take it off and bolt the new one on but on some you need special pullers etc,

Disregard the above and follow these instruction which will also allow you the replace the wiper motor or wiper pulse module if that is why you need to replace. They are part of the same assembly. First disconnect the negative side of battery then look under the passenger side of wiper arm. You will see the motor end of the assembly. There is a arm attached by (2) #8mm bolts Remove one completely and the other back off enough to dislodge the arm. You will see 3 # 10mm bolts in a triangle configuration, remove them. You will have to slide the motor assembly to the left until it dislodges from the bracket. At this point unclip the electrical plug (black in color), you will now have the unit free to replace motor or pulse module. The pulse module is attached by 3 torks screws and can be lifted out after removal. I just replaced mine on 4/23/11. If i had this info earlier it would have saved me a lot of stress. Good luck.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

chances its not the motor but the wiper module board located on the wiper motor. just remove the wiper motor and the module board is connected to it.

User Avatar

You will need to take out the whole motor to replace it. It is usually best to get a mechanic to take care of it.

User Avatar

where is the location wiper motor Pontiac grand prix 2002

User Avatar

Just above the strut top, passenger side under the hood

User Avatar

It is located inside the frame that contains the wiper motor and reduction gear. You should take the whole wiper system off in order to get an access to the board.

User Avatar

$55.00 for the part and $75.00 to install. So $130.00

User Avatar

under the air vent next to the windshield on the outside of your car

User Avatar

Remove the wiper arm, then the nut that is is on the part you see from the outside. Lift the lift gate, and remove the platic trim panel by using trim remover tool. disconnect the electrical connector, and remove the mounting bolts that hold the motor in place.

User Avatar

The 1993 Pontiac Transport windshield wiper control module is located on the firewall in the engine compartment. The windshield wiper control module will be on the passenger side of the firewall.

User Avatar

How to replace wiper motor on a 1998 montero sport mitsubishi

User Avatar

how do you replace rear wiper motor on a 1997 ford explorer

User Avatar

Remove the wiring harness from the wiper motor. Remove the windshield wiper arm from the wiper motor. Remove the wiper motor retaining screws. Reverse the process to install the new wiper motor.

User Avatar

Remove the wiper arm from the wiper motor. Remove the wiring harness. Remove the wiper motor retaining bolts. Reverse the process to install the new wiper motor.

User Avatar

how do you replace a wiper motor in a 2000 jetta?

User Avatar

where is the wiper motor on a 1996 Nissan Maxima GXE

User Avatar

check linkage assymbely or the transmission mounted on the wiper motor. you might have a bad wiper transmission.it will be only $34 change it should fix the problem

User Avatar

Remove the wiper arm from your 1999 Oldsmobile Cutlass wiper motor. Remove the wiper motor wiring harness. Remove the wiper motor retaining bolts. Reverse the process to install the new wiper motor.

User Avatar

Check the switch and make sure it is working. If it is, the problem may be the wiper motor itself, which will be located inside the rear panel on the back door...the wiper will be connected to it.

User Avatar

You will have to remove the wiper arms, then remove the cowl, and then the wiper motor.

User Avatar

how do you get to and replace the wiper moter on a 97 marquis

User Avatar

Remove the 2005 Honda Odyssey rear wiper arm from the wiper motor. Remove the wiring harness from the wiper motor. Remove the wiper motor retaining bolts. Reverse the process to install the new wiper motor.

User Avatar

Remove the wiring harness from the wiper motor. Remove the wiper arm linkage. Remove the wiper motor retaining bolts. Reverse the process to install the new wiper motor.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.