Car Computers and Sensors
Dashboard Lights and Gauges
Acura Integra
Toyota 4Runner
Toyota SR5

How do you reset a maintenance light on a 1995 Acura Integra?

676869

Top Answer
User Avatar
Wiki User
Answered
2015-07-16 18:24:46
2015-07-16 18:24:46

The maintenance light can be reset by pressing the red reset button on the right side below the ignition area, pass the panel.

If you don't mind looking under the steering column, you should be able to see it.

there is a little switch under the dashboard on the drivers side under the steering wheel just flip it and it should go off

You will find a switch under the steering wheel area. It may be a black retangular plastic unit, with a blue push switch. In order to turn off the Maintenance Required signal, you must first, start your car on, then click the switch a couple of times until the Maintenance Required signal turns off. If you can't find it by touch, find it using a flashlight.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


How to reset maintenace light on 1999 acura t l 3.2

The easiest way to reset the check engine light on a 1995 Acura Integra is to unhook the battery for a few minutes. If the light is still on after hooking it up again, there is probably still a problem that needs to be fixed with the engine.

I have a Acura Integra LS 1995 with an Acura Stereo, I have the Code but I can Not reset it , what are the steps to reset it? please help me ...

Just hold the trip reset button until the light go off,it will flashe and then come off

Usually your oil needs changing. You have to reset the light yourself. Look in manual it will show how to reset it.

There is a small square button underneath the dash just to the right of the steering collumn. With the key in the ignition, in the off position, press the button for 7-10 seconds, then turn the key to ACC. This should reset the maintenance required light. It is a gimmick to get you to take your vehicle to the dealership so they make money off of you for resetting it.

Press and hold the select AND reset buttons at the same time. Turn ignition switch to on and wait maybe 10 seconds until the maintenance light goes out.

Turn key to position 2 and hold select and reset together for 10 secounds

how to reset maintenance light on mercedes s550 amg

i only want to repair my car without taking it in to the dealership, thank you

To reset Maintenance light, switch key to on position, do not start. Press select and reset buttons at same time for about 15 to 20 seconds, then switch key off. If reset occured, the light will go off when you restart engine. If not, repeat process. Took three time for me.

press the reset and select switch at same, turn ign. key to II (On) and wait 10 seconds

reminder to change oil you can reset it by inserting your key its actually pretty useless

how do i reset the check engine light on a 1999 acura 3.2tl

How to Reset Maintenance Warning Light on a 2008 Toyota 4Runner

The check engine light comes on when a problem has been detected, you have to fix the problem to get the light to turn off. You can have the problem code read at most auto parts stores for free. To reset the light, disconnect the battery for one minute.

Depending on the mileage on the car, there are some maintenance requirements to be done by you, or the car dealer. The maintenance light will stay "on" until these maintenace issues are completed. Your owner's manual also tells you how to reset the maintenance light, and outlines the maintenance required per the mileage on the car.

Not quite sure how to do it manually, but if you spend the extra couple of dollars to go to a Acura dealer they will reset all the warning lights on the vehicle.

Underneath the dash on the driver's side, near the steering column there is a button, square. Hold it for 10 - 15 seconds. The light will go off.

Resetting the maintenance light on a 1999 Toyota Tacoma is very easy to do. To reset the light, take the battery cables off for up to one minute to reset the light.

Push the select and reset switch at the same time, turn the ignition switch ON (II), and hold them more then 10 seconds. The above sentence came straight from the 2001 Acura TL service manual

Your owners manual should tell you how to reset the light.

To reset "MAINTENANCE REQUIRED" light, turn ignition off, press and hold the SELECT and RESET buttons. Turn ignition and hold buttons for 10 seconds until the indicator resets. works on 2003 mdx for sure.

You can reset the light by disconnecting the battery negative cable and waiting a few minutes. If the fault that caused the light to come on is not repaired, it will come back as soon as the monitor that controls it is rerun.

If timing is bad on a 1990 Acura Integra they car will either run incredibly rough out not at all. To fix the timing be sure to correctly align the distributor to the right factory specified degree.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.