How do you reset security system on Chevy Impala?
In Chevy Impala
On my 03 all I had to do was turn the key on and press the gas pedal all the way down 3 times for 5 seconds.
1 person found this useful
Place the key in the "Run" position, but don't start it. Walk away. Come back in about 20 minutes. Turn off the key. Start the Blazer. You're done.
Take it to your Dealer for repairs. It could be any number of sensors or the contacts in the column.
Answer . I'm told this is a common problem that Chevrolet is aware of. Contact your local dealer. They should be able to replace the ignition switch and charge it back to Chevrolet as a warranty repair.
many early 90's gm cars the computer is reset auto what you want it to do is learn it's idle . you may try to put car in drive with all electrical devices turned off apply park brake and chock wheels so car will not move now just sit there and wait with car running in drive until the electric fan tu…rns on this can take as long as 20 minutes.. when fan turns on it has cycled and should have learned it's new idle...note it has taken me as many as three times for it to catch...turn car off and restart and see if your idle has smoothed out .. this is common when disconnecting the battery.. now i plug in an outside power source in to the lighter to have computer hold it's memory ( Full Answer )
Answer . \nYou should be able to reset the low coolant light by the parking light switch 3 times on and off somewhat quickly should do it
If you want your service engine soon or check engine light reset than you can disconnect the battery. If you want the security light out you have to hook up a battery charger and turn your key to the on position without starting it. Wait at least 15 minutes, then turn key back to the off position an…d then try to start it. ( Full Answer )
Answer . \nYour security light does not reset, it comes on when your door is open and your key is not in the igition and it will continue to flash, even when doors are closed. This is GM's cheap way of looking like it has advanced security features.. but it doesn't, don't worry about it, it mea…ns nothing it, and it is meant to do that. Now if you want to reset your oil light, turn the ignition to the on position, pump your gas three times, all the way to the floor. If it doesn't work, try doing it a little slower... all the way to the floor, release, all the way to the floor, and again.. it should blink, change engine oil. ( Full Answer )
Press and hold HR or MN buttons, located below the tune knob, for two seconds. Then press and hold the HR button until the corect hour apears do the same for the miniutes. Always use FM to syncronize your time keeping in mind AM-PM . Hope this helps signed Chris in northern Ontairo
To reset the security system for a 1994 Cadillac, first turn offeverything including the radio. Place key in the ignition, halfturned on, and wait for 20 minutes. This will automatically resetthe security system.
Odometer tampering is an illegal practice and a serious crime. So it might be better for you to see an authorized dealership to have anything done with your odometer.....
Put your Chevy Cavalier in neutral and then crank it once withoutstarting the car. This will turn on the electrical system and youneed to allow it to sit like that for several minutes foreverything to reset itself.
There is a bolt on top of the thermostat housing itself. using a very small metric socket open slightly to relive trapped air pressure in side of engine. This works on the 3.8l Ls models as far as i know.
More than likely its the ( E.C.M) engine control modular, And has to be programed.
See Tire Pressure Monitoring System on page 5-65 of your "Owner's Manual", under Section 5: Service and Appearance Care - Tires...
If you have set the alarm system off, lock the driver door, and then unlock it with the key and that should reset the security system.
make sure everything is off (radio, etc). place your key in the ignition, half turned on, for 20 min or so and that will reset the security system. i had to do this with my 2000 deville and it worked. try it at your own risk. goodluck
See How to Reset the Change Engine Oil Message on page 6-18 of your "Owner's Manual", under Section 6: Service and Appearance Care - Engine Oil...
See Content Theft-Deterrent(If Equipped) on page 2-12 of your "Owner's Manual", under Section 2: Features and Controls...
Turn on the ignition but do not start the engine. Depress the accelerator to the floor 3 times within 5 seconds. The oil light should blink and then go out.jd
You can bypass the factory security system in your 2004 ChevroletImpala by removing the factory security system fuse. You can findthe factory security system fuse in the fuse box.
In most cases, the security system will reset itself after 10minutes. You can also remove the ground cable from the battery.
No such thing as a "reset" you have to fix the problem. Probably broken wire on key lock cyl. or bad key.
I'm gonna be honest... the best thing might be to take it in to a shop. I don't know about this condition! If I did, I would have, quite simply, brought it to the dealer, or a certified GM Goodwrench technician. Costly? Maybe, but most of the cost is labor, not parts. So, with that, I'll say it agai…n: Bring It In. ( Full Answer )
To Reset the security system you disconnect the battery for 5 min then reconnect it. make sure you have your remote or access to the controls because the alarm will sound when the battery is reconnected. when it sounds hit the off button make sure you retighten the battery cables correctly and y…our good to go. You can also reset the alarm system by disconecting the power to the alarm it's self if you know which wires are for the alarm. There will be one wire that's constant 12v that's the one that should be disconnected, there is also a 12v switched that connects to your ignation wireing . This wire is how the alarm knows when your starting the van or turning it off. ( Full Answer )
I don't know about a reset, but there is a Fuse identified as CRUISE (Cruise Control Steering Column Controls) located in the Driver's Side Instrument Panel Fuse Block. See page 5-95 in your "Owner's Manual" for details.....
most GM vehicles you turn the key to the on position (don't start) and depress the gas pedal 3 times within 5 seconds.
The Impala, as well as other GM models, have a passive theft deterrent called 'Passlock' which will prevent your car from starting if there was an attempted theft or other unauthorized entry into the ignition. However, this same system is prone to randomly and sometimes frequently engage itself even… when the car is being used properly. Solutions: 1) If the car will not start or "crank", turn you key in the ignition to the 'on' position and leave it there for a minimum 20 minutes. After 20 minutes, turn the key to the 'off' position for two minutes. Now attempt to start the car. This is a built-in feature of the Passlock system to override the security lock. 2) If this does not work, you may need to have the car taken to a dealer (a regular mechanic will not be able to guarantee a fix). They will check for a diagnostic code, and if one is present which relates to this system, they will advise that you replace the BCM (Body Control Module), ignition cylinder, and the ignition switch. This will be around $800 depending upon your dealer and where you are located. Unfortunately, unless you systematically isolate each component, you may not know which part is actually causing the problem. However, the most likely culprit is a faulty ignition cylinder or a bad BCM. The BCM's are known to be "buggy". GM is well aware of this problem, but they will not issue a recall. Hope this helps a little. ( Full Answer )
you can do 2 things for this 1 you can turn the key off and on 3 times or 2- you have to go into radio and to re set the oil life to do that turn the car on,,,do not start it.. then turn the radio off press the on buton of the radio and hold it until you see the radio setting appear .….then use the arrow to move the option to get to the oil life symbol..then re set it there..\ hop this helped/ ( Full Answer )
Read closely, This will take 33 mins. to do. Get in your truck with a watch, Turn key to start mode and as soon as you here the starter, turn key loose not off. Then wait 11 min. no more and no less 11 min. only After 11 min. turn key off, then repete the same steps 2 more times. Then after th…e last step is done, turn key off, Then start truck, Your done. If truck don't start. Then repete all the steps again, to make sure it was only 11 min. each time. BEFORE YOU DO ANYTHING CHECK THE SECURITY FUSE IN FUSE BOX. ( Full Answer )
exhaust manifold, exhaust pipe, catalytic converter, muffler, tailpipe, and hangers. Sometimes a resonator is included as well
unlock doors, then exit vehicle and lock the doors two time, then go to the other side and unlock it, that should reset the system
How do you reset the stereo system when it reads SEC 1999 Toyota prado it looks like it has been done 9 times before
You can reset the 2002 Chevrolet blazer security system by removingthe security system fuse. Keep the fuse out for 10 seconds andreplace it to its original slot.
The Chevrolet Imapla has been produced for many years. Early models had standard manual and automatic transmissions. Current models are also fitted with ABS and ESP systems.
In most cases the theft deterrent system in your 2007 ChevroletImpala will reset itself in 10 minutes. You can also remove thefuse for 10 seconds and replace it to reset the system.
The security light on a 2001 Chevy Astro Van can be reset bydisconnecting the battery for 30 seconds. This resets the systemand turns out the light until another problem is detected.
Well i have a 2001 cheverolet malibu.....my wife's car. If you dont have access to your manual the first thing to do is get car in a position that is flat in nature. Then turn your key just to the on position(not starting engine) Then just sit and wait for approx. 15 minutes or so the security light… will flash a couple of times. Then you turn the key off and then start your engine......Face toward Mecca and pray.....LOL this should do the trick if not. You may want to think about taking it to shop. I just bought a 05 impala..and paid to have low tires light go off..u just hold the radio button until the radio says security..then scroll by radio power button to what option u r lookin to fix and reset it..the first button u push is the tune button..sorry and with car running..and exit when done ( Full Answer )
Turn ON the ignition, with the engine OFF. Attempt to start the engine, then release the key to ON. The vehicle should start and then immediately stall. The SECURITY light should come on. After approximately 10 minutes, the light will turn off. Turn OFF the ignition and wait 5 seconds. Re…peat steps 1 through 4 two more times for a total of 3 cycles/30 minutes. The vehicle is now ready to relearn the security system on the 4th attempt to start the engine. ( Full Answer )
Just disconnect the negative cable from your battery for a good ten to fifteen minutes so that the main does itself a reset.
My 1991 CORVETTE WAS FINE, THEN 3 DAYS LATER IT WOULD NOT START. A FEW. YEARS AGO MY CAR WOULDN'T CRANK OVER, I CALLED MY FRIEND AT A CHEVY DEALER HE TOLD ME TO CK. FOR A LOSE WIRE ON THE V.A.T.S SURE ENOUGH A WIRE CAME LOOSE. FIXED IT AND MOTOR. CRANKED OVER AND IT STARTED. NOW IT MOTOR TURNS OVE…R BUT DOES NOT START. I KNOW FROM RESEARCH THAT V.A.T.S. CONTROLS STARTER,FUEL, & STEERING WHEEL LOCK. MY ? IS IF MOTOR IS TURNING OVER IS FUEL ALSO OK TOO? OR IS THERE SEPARATE WIRE ON THE V.A.T.S. THAT COULD OF CAME LOOSE? ( Full Answer )
On a 2004 you just turn off the radio and hold down the display button until you hear a beep and a menu comes up. Press the seek button until you get to tire monitor. Reset tire monitor and turn radio back on. Probably same for a 2006.
The ABS light is on because there is a problem with the system. Until the problem is fixed the light will remain on. Once the problem is fixed the light will reset itself.
Expert: john replied 1787 days and 3 hours ago.. HelloCustomer I am sending the programming instructions for your theft deterent.If this proceedure does not work you have a problem that must be repaired first.I would start by scanning the vehicles computer system for failure codes. Programm…ing Theft Deterrent System Components Programming Replacement Passlock TM Sensor, BCM, or PCM Important: . â¢. The body control module (BCM) must be programmed with the proper regular production option (RPO) configurations before performing learn procedures. Refer to Body Control Module (BCM) Programming/RPO Configuration in Computer/Integrating Systems.. â¢. If replacing the BCM with a GM Service Parts Operations (SPO) replacement part, the module will learn Passlock TM sensor data code immediately. The existing powertrain control module (PCM) however, must learn the new fuel continue password XXXXX the BCM is replaced.. â¢. If replacing a PCM with a GM SPO replacement part, after programming, these modules will learn the incoming fuel continue password XXXXX upon receipt of a password XXXXX Once a password XXXXX is received, and a password XXXXX XXXXX a learn procedure must be performed to change this password XXXXX A PCM which has been previously installed in another vehicle will have learned the other vehicles fuel continue password XXXXX will require a learn procedure after programming to learn the current vehicle password.. Conditions Use this procedure after replacing: . â¢. The Passlock TM sensor. â¢. The BCM. â¢. The PCM. Learn Procedures There are 2 available methods to perform the programming procedure: . â¢. A 10-minute procedure which requires a Tech 2 and a techline terminal.. â¢. A 30-minute procedure which does not require the use of any tools .. 10-Minute Learn Procedure . Connect the Tech 2 to the vehicle. . Select Request Info. under Service Programming System and follow the instructions. . Disconnect the Tech 2 from the vehicle and connect it to a techline terminal. . On the techline terminal, select Theft Module Re-Learn under Service Programming. . Disconnect the Tech 2 from the techline terminal and connect it to the vehicle. . Turn ON the ignition, with the engine OFF. . Select VTD Re-Learn under Service Programming. . Attempt to start the engine, then release the key to ON, vehicle will not start. . Observe the SECURITY telltale. After approximately 10 minutes, the telltale will turn OFF. The vehicle is now ready to relearn the Passlock TM Sensor Data Code and/or password XXXXX the next ignition switch transition from OFF to CRANK. . Turn OFF the ignition, and wait 5 seconds. . Start the engine, the vehicle has now learned the password. . With the Tech 2 scan tool, clear any DTCs. 30-Minute Learn Procedure . Turn ON the ignition, with the engine OFF. . Attempt to start the engine, then release the key to ON, vehicle will not start. . Observe the SECURITY telltale. After approximately 10 minutes, the telltale will turn OFF. . Turn OFF the ignition, and wait 5 seconds. . Repeat steps 1 through 4 two more times for a total of 3 cycles/30 minutes. The vehicle is now ready to relearn the Passlock TM Sensor Data Code and/or passwords on the next ignition switch transition from OFF to CRANK. Important: The vehicle learns the Passlock TM Sensor Data Code and/or password XXXXX the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle. . Start the engine. The vehicle has now learned the Passlock TM Sensor Data Code and/or password. . With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles. Expert Type . Master A.S.E Automotive technician. Category: . Chevy . Pos. Feedback: . 99.2 %. Accepts: . 4071. Answered: . 3/15/2008. Experience: A.S.E MasterTechnician A1-A8 w/L1,38 years experience General Motors Master Technician. Ask this Expert a Question >. ( Full Answer )
use a scan tool even a basic one from autozone if you know the guy working there he can reset it on the scan tool, you can disconnect the battery for 2 days. when i had mine unplugged doing some motor work, I had to drive around to pass emissions pcm had reset so i could pass the emissions test. hop…e this helps. ( Full Answer )
Pretty much like all water cooled engines. The radiater is a pressurized heat exchanger that allows water to pass through tubes and air to pass over the tubes to transfer the heat from the water to the air. The water is pumped by a water pump through the water jackets molded into the engine block. W…here the heat from the block iks transferred to the water. The water then continues back out to the radiator to be cooled again. The temperature is regulated by a thermostat located on top of the engine block and cooling fans to ensure proper airflow across the radiator for cooling. ( Full Answer )
The abs light is on because you have a problem with the abs system. The light will remain on until the problem is fixed. Once the problem is fixed the light will reset itself.
Because there are no sensors to tell the car when you get your oil change, that is why they give you the option of reseting it manually using the radio buttons. Check your operators guide for directions.
Just install the new 1 and go drive it a few miles. If you are asking how to turn the check engine light off, Then you will need a engine scanner to clear the codes. Some parts stores will do it for you FREE.
This can be done with a code reader that has the ability to wipe codes. It can also be done by removing the battery for 10 minutes. All vehicle systems should be auto reset.
It takes a special computer that can type command prompts to ECU. Look for an auto locksmith on Craigslist that does chipped keys, etc. under services and is mobile. It will take about 5 minutes and should cost less than 100.00. Do not go to the dealer, they charge 5x as much. Just tell locksmith PA…TS system activated-needs reset. ( Full Answer )