Ford Escape

How do you reset the change engine oil light on a 2005 Ford Escape?

505152

Top Answer
User Avatar
Wiki User
2007-03-23 15:11:28
2007-03-23 15:11:28

Previous post read: This answer although informative is incorrect for the question asked. If the person had asked about "Check Engine Oil Light" then the answer would be correct. Re-reading the question properly, the person asked about "CHANGE Engine Oil" as displayed in the driver information center on the left side of the cluster. The reset procedure for this is simple once you know how to do it. Underneath the radio there are six buttons. The third one over is the "Info" button and the fourth one over is the "Set" button. Press the info button several times until it displays System Check. Press the set button to enter the check. If the first item to come up is not oil life then press the button until oil life is displayed. It likely says 0%. Press and hold the set button to reset the oil life to 100%. Done. You're welcome. ~Jeff~ aka. OttoPhickser

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

reset after the engine oil / filter change, service

User Avatar

Change your oil. The light can be reset with a code reader by any mech & is usually done at time of service. On some cars, disconnecting batt. long enough will reset them, although sometimes come back on.

User Avatar

The check engine light has nothing to do with an oil change. The check engine light is reset with a scan tool after repairing the failure that caused it.

User Avatar

The check engine light does not come on for an oil change.

User Avatar

The check engine light has nothing to due with an oil change.

User Avatar

The service engine soon is the same as a check engine light. It has nothing to do with an oil change.

User Avatar

The check engine light does not come on when an oil change is due. The check engine light is for an emissions related failure. It is reset with a scan tool after the fault is repaired.

User Avatar

how do you reset the check engine light on a 2005 Toyota tundra

User Avatar

The change oil light is reset by turning the key on, engine off, and pressing the gas pedal three times.The check engine light can only be reset with a scan tool. The cause of the fault needs repaired or the light will return.

User Avatar

To change a check engine light the dashboard must be removed this is best done by a mechanic. To reset a engine light unplug the cars battery for half a hour.

User Avatar

There is no reset button for the check engine light. You can have Mitz. do it for $$$ or you can remove the negative battery line for a few seconds and replace. That will reset the check engin light.

User Avatar

With engine off. Turn key to on. Press accelerator fully three times. This should reset light.

User Avatar

The check engine light has nothing to do with an oil change it is an indication of a failure of an emissions component.

User Avatar

After changing the engine oil, the system must be reset. With the ignition key to ON (engine not running), push the RESET button located in the driver's side instrument panel fuse block. The CHANGE OIL light will start to flash, press and hold the RESET button again. The reset is complete when you hear the chimes and the CHANGE OIL light goes out.

User Avatar

try to reset oil light on 528i bmw year 2000

User Avatar

A reset Engine Service Light comes on when an issue comes up with in the engine. This light can be reset by a tech or by fixing the problem.

User Avatar

You can usually disconnect the battery cable for about 15 seconds and reconnect it to reset the engine light. Check the fuse box for a(red) resert button - to reset the engine light disconnect battery for 15 minutes , the red reset button on fuse panel is for motor oil change reminder reset

User Avatar

what do you reset the cehck engine light patriot manual transmission 2008? thanks for you support.

User Avatar

To reset the oil change light on a Toyota Highlander 2012, switch the engine to the OFF position. Then switch the engine back on while pressing the trip meter reset button until it displays 000000 or says COMPLETE.

User Avatar

What engine light. If you are referring to the Check Engine light then reset it with an OBD2 scan tool after the problem is repaired.

User Avatar

Unhook the battery from the vehicle overnight. When you hook the battery back up it will be reset.

User Avatar

how do you reset engine light on 1991 volvo 240

User Avatar

how do you reset check engine light in 2008 buick lucerne


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.