Mobile Phones
Mazda 626
Facebook
Nokia Phones

How do you reset the code on a 1994 Mazda 626?

131415

Top Answer
User Avatar
Wiki User
2006-04-10 09:11:49
2006-04-10 09:11:49

First disconnect the "NEGATIVE" battery cable.Next depress the brake pedal for at least 20 seconds.Reconnect the battery cable.Now you need to run a jumper wire (just get a peice of wire strip both ends a little),find ypur diagnostic connector (located near your fuse box under the hood),you need to run the jumper wire form the "GND" terminal to the "TEN" terminal.Turn on the key to the "ON" position for at least 10 seconds,the start engine,run at least for 3 minutes at above 2000rpm.Shut off engine disconnect jumper wire,you're done.Hope it works for you.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

How do i change my 1994 mazda 626 alternater

User Avatar

A check engine code 332 for a 1994 Mazda 626 means that the EGR valve's voltage is lower than it is expected to be. The ERG valve is part of your Mazda's emission control system.

User Avatar

You can reset the ABS light in a 2000 Mazda 626 by unplugging the battery cables. You can also reset it by connecting a diagnostic tool to your car.

User Avatar

There is no such thing as a "termostat"

User Avatar

Either buy a reset switch from a motor factor or get your local dealership to clear it.

User Avatar

i have a 2000 mazda 626 with a 1744 code. i was able to pull the code but my scanner wont tell me what it is for. what does this code represent and how do i fix it?

User Avatar

The fuel reset button for a 1999 Mazda 626 is located inside the trunk of the vehicle. It will be on the left side close to the outer left tail light.

User Avatar

In a 1994 Mazda 626 : Both the 2.0 litre four cylinder engine and the 2.5 litre V6 engine have a timing BELT

User Avatar

Mazda 626 1.8Ltr 1997-2002 Engine code FP Is an interference engine.

User Avatar

It depends on if it is a v6 or l4.

User Avatar

where is the inertia switch on a 626 maza 1994

User Avatar

the Mazda 626 and the Mazda rx7 are interchangeble.

User Avatar

will a 1997 Mazda 626 transmission or engine interchange with a 1999-2002 Mazda 626 transmission or engine

User Avatar

Mazda B2000 Ford Escort Mazda 1994 626 Honda General Motors

User Avatar

how many belts are in mazda 626

User Avatar

at the bottom of the air filter housing.

User Avatar

Was wondering the same.. for a Fuel injected 1987 Mazda 626 non-Turbo According to a Mazda dealer I just called. There is no reset switch. The Fuel pump is located in the gas tank. and the Pump Relay is on the firewall of the passenger side. Regards, Yanek What do you want to reset? "Check Engine" codes can be reset by disconnecting the battery for 5-10 minutes.

User Avatar

i have a mazda 626 and the engine light came on what do i do and how do i fix it

User Avatar

The 1994 Mazda 626 was built with 4 and 6-cylinder option models. The CD4E transmission has a fill of 7.4-quarts (qts). The GF4A-EL has a larger capacity of 9.3-qts.

User Avatar

Go to Advanced Auto. They should be able to.

User Avatar

how do i troubleshoot my 1998 Mazda 626 distributerless no spark

User Avatar

its in the back of the engine under the intake manfold


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.