Turn ignition on, don't start the engine, just ignition on, press the odometer button in and hold in. (make sure your odometer is reading the actual milage, not the trip meter)Turn ignition off while still holding od button in.Turn ignition on again, still holding od button in, the od reading will displayshort dashed lines like this: ------. Keep holding the button in.Watch as the dashed lines begin to decreas and finally disapear.The odometer then should return to reading out the milage again, and the maintenance light will not come back on. At leats not till you reach another5000 miles. It is dsigned to come on and bug you as you reach 5000 mile intervals. Resetting this maintenace light will in no way shape or form hurt your Toyota.This "maintenance" light is a clever way to get you to see the Toyota service department. Good luck.Jeff
how do you reset the check engine light on a 2005 Toyota tundra
How to Reset Maintenance Warning Light on a 2008 Toyota 4Runner
A maintenance light on a Toyota Camry can be reset by your mechanic after you have the work done that is needed. You also may be able to get instructions by checking your manual.
How do you reset maint read light on 2010 corolla
maintenance with engine
Resetting the maintenance light on a 1999 Toyota Tacoma is very easy to do. To reset the light, take the battery cables off for up to one minute to reset the light.
To reset the dash light indicators on a Toyota Tundra the trucks ECU will need to be reset. The simple way of resetting the ECU requires disconnecting the battery for 5 seconds. When the ECU is reset the lights will be clear.
How do you reset the maintenance required light in the 2011Toyota RAV4 with a smart key starting system
disconnect the battery
press and hold trip/reset button turn key on, do not start. Wait for dash lines to go off in odometer reading space, once they have gone off release trip/reset button, turn key off: that should reset light.
Here is the link on how to reset and change engine oil on 08 tundra ( http://www.tundraheadquarters.com/documents/toyota-tundra-5-7-liter-oil-change.pdf )
You can turn off the low tire light, on your 2005 Toyota tundra, by holding in the reset button. You can also remove the fuse for 10 seconds and replace it to its original slot.
how to reset maintenance light on mercedes s550 amg
In most cases the Toyota tundra factory alarm will reset itself after 10 minutes. You can also pull the fuse out for 10 seconds and replace it to reset the alarm.
Your drivers manual should give you the information to reset the oil maintenance light.
Set it to trip A and hold reset turn ignition off then turn ignition on and maintenance light will flash and your done.
You will need to take it into a mechanic. They will be able to check out your vehicle and then they can turn off the light.
How do you reset maintenance reminder light on 2008 Toyota corolla? For what it is worth: To reset the Maintenance Required light on my 2007 Toyota Corolla: 1) Set your trip meter to the odometer setting (in other words, not Trip A or Trip B) 2) Hold down trip meter reset button and turn ignition to off. 3) While holding down the trip meter reset button now turn the ignition to on. 4) Keep holding down button until Maintenance Required light shuts off. Note: One some other Toyota models you hold down the Trip A meter rather than the odometer. Hope this works for you.
I dont know how to turn that sensor off; although, i do have a 2006 tundra and if your spare tire is low that light will come on as well so you might want to check that out.
With the ignition switch in the off position, hold in the hold in the trip odometer. Now turn on your key and you will see a series of zeros begin to appear. Once that stops, your maintenance light will be reset.
A person can reset the maintenance required light on a 2004 Toyota Sienna by holding down the odometer trip button. A series of zeroes will appear, which indicates that the light has been reset.
Put the key into the ignition and press the odometer button. While holding down the odometer button, turn the key to the on position. You will see "-----"on the odometer display. It will count down "-----" "----" "---" "- -" "-". Then you will see zeros on the odometer display "000000". You can now release the odometer button. This will reset the maintenance light on your dash!!!!!!
There are pages and pages of things that can cause a check engine light. You need to have it checked with a scantool. Then the code can be diagnosed and repaired.
Disconnect the negative battery cable for 5 minutes. If that does not reset the Check Engine light you will need access to an OBD2 scan tool.