Make sure odometer is on the mileage screen (not TRIP A or B), insert ignition key but do not turn. Then Hold down the reset button, turn the ignition key to the ON position only. Keep holding the button down until the mileage zeros out. Hold it down until the mileage comes back on. Turn the ignition off and then on, the Maintenance required light should be off now.
A maintenance light on a Toyota Camry can be reset by your mechanic after you have the work done that is needed. You also may be able to get instructions by checking your manual.
How do you reset the maintenance reminder screen on a nissan micra sve?
how do you reset anti theft on a 1994 toyota camry
That is reset with a scan tool.
The "Maintenance Notice" screen will be reset when: "Reset Distance" is selected, or "Interval Reminder" is set to off.
How to Reset Maintenance Warning Light on a 2008 Toyota 4Runner
Check your owner's manual. It's in there. So easy, I just can't remember for now.
how to reset oil timing on 1990 toyota
Toyota does not use inertia/reset switches.
How do you reset maintenance reminder light on 2008 Toyota corolla? For what it is worth: To reset the Maintenance Required light on my 2007 Toyota Corolla: 1) Set your trip meter to the odometer setting (in other words, not Trip A or Trip B) 2) Hold down trip meter reset button and turn ignition to off. 3) While holding down the trip meter reset button now turn the ignition to on. 4) Keep holding down button until Maintenance Required light shuts off. Note: One some other Toyota models you hold down the Trip A meter rather than the odometer. Hope this works for you.
This is how to reset "Maintenance Required" light on Toyota Camry with "Smart Key" feature.This works on 2007 and newer Camry models, including the Camry Hybrid. Put the odometer on "Trip A." Turn off the car, hold down the odometer button and, without putting foot on the brake, push "Start" button twice (while continuing to hold down the odometer button). Watch the display . . . it will speak for itself.
To reset the reminder light on a Toyota, you need to turn the ignition key forward without starting the vehicle. You then need to pump the gas peddle 3 times within 10 seconds and it will reset the reminder light.
hold odometer reset button down with key off, turn key while holding down reset button until lights flash and go out
how do you reset the low tire pressure warning light on a 2009 camry
Turn key off. Push mileage reset button. Keep it pushed in while you turn ignition key to on position. Hold for 10 secs...
There is no such button.
maintenance with engine
You need a special computer for that. Check the gas cap first, make sure its tight, sometimes that sets it off.
you will go to the toyota dearler it good pleace
To reset a 2007 Toyota Rav4, the steps are as follow:= = 1. Move odometer to Trip A then hold down. 2. Turn off ignition then turn on to ACC. (Don't turn on engine). 3. The reset will go through 000000.00 then _ _ _ _ _ going to ---- going to --- etc. 4. Once it runs through the reset, the maintenance required light flashes and goes off. 5. Easy fix, not sure why Toyota doesn't have this in the manual.
Replace the bulb that is burnt out.
The fuel reset button for a 1992 Toyota Camry is in the trunk behind the fabric on the passenger side. On some models of Camrys, the button is on the passenger side under the dash.
Beaverton Toyota, Oregon, provides a list of the steps to reset the service indicators for a variety of Toyota models, also Scion. Go to: How To Reset Maintenance Light ( http://www.beavertontoyota.com/service/tips.htm ) FIND your make and year, and go to the list, thus ... --- "Reset Engine Oil Replacement Reminder Light" --- FIND your model and follow the detailed steps. For 2008 Avalon, the list is at: http://www.beavertontoyota.com/service/pdf/08maintlight.pdf
It is reset with a OBD2 scan tool, after the repair of the system.
AnswerStart by making sure the odometer is on actual mileage. Turn the key "off" press and hold the "reset" button on the upper left of the instrument panel. Turn the key "on" (engine off); the maintenance light will flash then turn off. Release the "reset" button and it's done!