answersLogoWhite

0


Top Answer
User Avatar
Wiki User
Answered 2007-11-24 22:00:04

The GM Oil Life System calculates when to change your engine oil and filter based on vehicle use. Anytime your oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where you change your oil prior to a CHANGE OIL message being turned on, reset the system. Always reset the engine oil life to 100% after every oil change. It will not reset itself.

To reset the CHANGE OIL message, do the following:

1. Press reset stem till it Displays "OIL LIFE" on the DIC.(3 times)

2. Press and hold the reset stem. The oil life will change to 100% and a beep will sound.

3. Turn the key to LOCK. If the CHANGE OIL message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.

Hope This Helps.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Loading...

Still have questions?

Related Questions

Is there a way to reset the engine oil level indicator on a 2003 Tahoe?

Change engine oil, or check oil indicator?


How do you reset service indicator Mercedes ml 270 cdi?

The service indicator light, in your Mercedes ML 270, can be reset by holding in the engine oil life button. The engine oil life will go to 100 percent. The service indicator light should go off.


How do you reset the change oil indicator on your husqvarna 2246 tractor with the Briggs and Straton v-twin engine?

Oil change indicator will come on at 49 hrs for two hrs of operation than will reset itself.


Does your check engine light in a 1993 Honda civic indicator a low fuel level?

no you have to change air sensor


What causes a engine knocking noise when you are accelerating and the engine is warm doesnt do it when engine is cold?

Most likely needs a tuneup done. Check the timing and change the normal tuneup part.


How often should i change my battery in my f-150?

only need to change a battery if the battery is not holding a charge suffient to start the engine


What is watt engine indicator?

A watt engine indicator is used to perform a measurement of the amount of steam pressure in a cylinder. This process is completed with the assistance of a manometer.


How do you reset check engine light after oil change was done on 2003 cvalier?

The check engine light has nothing to do with an oil change. It is an indicator of a failure of a component that will cause an increase in emissions. See related questions below for more info.


2003 Tahoe Z71 There is an indicator for the air filter How do you read the indicator to determine when it's time to change the filter The manual is of no help?

When the red sleeve shows in the window, the air filter is clogged. the indicator is connected to the engine side of the air filter, and the increase in vaccum causes the indicator to trip. It can be reset by pushing in the button on the end.


What is malfunction indicator light?

A malfunction indicator light is also known as a check engine light. It is a light on the dashboard of a car that goes on when there is a problem with the car's engine.


Why does the control indicator for engine electronics stay on?

What indicator are you referring to? Are you referring to the Check Engine light? If so, it is on because the ECU has detected a problem with the emissions system.


Why does your car wine when you step on the gas?

It would be your cerpentine belt that runs our "extras" on your engine or your transmisson. Best thing to stop it would be to change the belt under the hood on the engine. If that doesnt work change your transmission fluids.


How can you fix your engine temperature indicator on your '95 civic Lx It never lift properly to show you that the engine warms up It stays at the bottom you replaced the antifreze .?

possibly change the temperature sensor???


RuneScape cheat engine?

doesnt exist. runescape doesnt have cheats sorry


How do you change a starter in an 1987 88 delta Oldsmobile?

disconnect the battery, then the wires from the starter. Then remove the bolts holding the starter to the engine.


How do you get rid of the service engine mileage indicator on a 2006 Honda Accord?

Turn key to on position with out starting. Press the select/reset knob until the "engine oil life indicator" is displayed. Hold down the knob for at least 10 seconds. The "engine oil life indicator" will blink. Hold down the select/reset knob for at least 5 seconds. The "engine oil life indicator" will be reset to 100%.


How do you reset the change oil indicator on a 2010 Chrysler Sebring?

Key on, engine off. Press the gas pedal to the floor three times in ten seconds.


Check engine light on Honda Pilot?

The check engine light on the Honda Pilot is an indicator that there may be a problem with the engine. This could be minor such as air or water in the gas tank or could be an indicator of something more serious.


How do you reset the Performing Service light indicator after a maintenance on a 1996 Jeep Grand Cherokee Laredo?

Simply turn on your engine, then momentarily press select button display followed by holding down the set button


Explorer engine oil change soon light stays on?

If an Explorer engine oil change soon light stays on, the sensor needs replaced. The sensor may also need reset by holding the button down for five seconds.


Does the check engine indicator bulb have a fuse?

Yes.Of couse it does.


How do you change over a premium gas engine to regular gas?

It doesnt require any work all you have to do is fill it up with regular gas.


What is the difference between the service vehicle soon and the service engine soon light a Pontiac aztek?

The Service Vehicle Soon indicator is usually a light bulb, headlight, or something to do with the vehicle. The Service Engine Soon indicator is anything that could be wrong with the Engine. Some computers can read codes for either, but some computers can only read codes for the Service Engine indicator.


How do you reset the oil change indicator on a 2009 Jeep Patriot?

Turn the ignition on, with the engine off. Press the gas pedal to the floor three times in ten seconds.


How do you reset the change oil indicator on a 2008 dodge ram?

turn the key on, engine off, press the gas pedal to the floor three times. cycle key