0
How do you route a 2006 Town and Country's trailer wiring harness?
Wiki User
∙ 15y ago
Get a wiring kit that has the in-line connectors that plugs into your existing wiring harness. The kits come with instructions with the location of the connector for your van. Here is one example; http://www2.northerntool.com/product/200325022.htm
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you install trailer harness in 2004 Honda Odyssey?
Visit auto parts store and order Hoppy 43105 harness. Remove interiorrear panel just above bumper and interior driver side rear quarter panel (where the jack storage is). You will find an unused wiring harness that is taped out of the way. Use this to connect it to the harness and route the wiring into the jack storage area.
Where do you hook the brake light switch wire on a trailer brake controller on a 1998 Chevy pickup with a tow package?
Start from the rear where the factory trailer lights wiring harness is, or from the taillights/brakelights themselves. Follow the wire (I think it should be blue) from the harness or taillights to the wiring harness as it runs to the (driver's side) under hood fuse panel. Again, it should be blue in color. On a Tekonsha brake controller you'll hook the red wire to it anywhere along that wire. Hope that helps. According to http://www.4door.com (This site also has pictures for installation) there are two options for the 1998 Tahoes: The option UY7 trailer harness is for heavy-duty towing applications. A 30-amp fused battery feed wire and auxiliary circuit routes from the cowl-mounted junction block, along the body side rail, to the rear bumper crossmember. The harness for the brake/parking lamps is spliced from the rear lamp harness. The harness is at the rear bumper crossmember. A plastic strap binds the harness. Tape wrapped around the harness prevents short circuits. The 8 wires have the following functions: • Orange -- The 30-amp fused battery feed • Blue -- An auxiliary circuit for electric trailer brakes • Brown -- The taillamps and the license lamps • Light green -- The backup lamps • Dark green -- The right turn signal and the stoplamp • Yellow -- The left turn signal and the stoplamp • White (heavy gage) -- Ground • White (light gage) -- The center high-mounted stop lamp The UY7 option does not include a connector at the end of the harness. A qualified technician must wire the connector following production. # Attach the trailer harness wiring to the trailer • Bending • Binding • Breaking • The harness drags on the ground. # Strap the harness wiring to the vehicle in a manner that allows slack in order to prevent the following conditions: # Secure with tape or straps the trailer portion of the harness to the trailer tongue in order to prevent the harness from dragging on the ground. 4.1. Wrap the harness together. 4.2. Bind the harness with a tie strap in order to avoid damage. 4.3. Store the harness behind the rear bumper on the fuel tank. 4.4. Strap the harness with a band or a tie strap. # Secure the harness when the harness is not in use. The second wiring harness option is the UY1 camper wiring harness. The UY1 harness is under the vehicle. The harness is inside the frame rail. The harness is even with the front of the pickup box on the driver's side. The UY1 harness is for the brake/parking lamps. The harness has an auxiliary power feed. The wires have the following functions: • Dark blue -- A 30-amp fused auxiliary power circuit. The other end of the wire is taped to the wiring near the junction block on the cowl. • Dark green -- The right turn signal and the stoplamp • Light green -- The backup lamps • Yellow -- The left turn signal and the stoplamp • Brown -- The taillamps • White -- Ground # Route the trailer harness wiring between the frame and the bumper, or the camper and the body, in such a manner that slack remains in the harness in order to prevent the following conditings: # • Bending • Binding • Breaking • The harness drags on the ground. # Tape or strap the trailer portion of the harness (if used) to the vehicle in order to prevent the harness from dragging. 3.1. Wrap the harness together. 3.2. Bind the harness with a tie strap in order to prevent damage. # Secure the harness when the wiring is not in use.
How do you repair the wiring on your 2008 Chevy silverados rear lights harness after they have been cut?
Butt connectors and heat shrink is the route I'd go. Soldering the butt connectors in is the best way to do it.
Does anyone have a wiring diagram that shows how to hardwire trailer lights for a 1986 Toyota 4Runner?
go to a reputable auto parts or trailer supply store and purchase a trailer wiring loom that is specific for your vehicle. it is a unplug existing, plug in new ("t") loom affair. included in this loom is a "converter" for Toyota specific light systems. standard trailer system (2 bulb) Toyota (3 bulb). probably 30 to 40 unless you purchase at dealer. my Toyota was an '89 but I'm confident that this is the route to take.
What are some strange things about Delaware?
In Delaware there is a trailer on route 13 near dover that is half abandon airplane half trailer it is called the airplane trailer.
How can you disconnect wiring harness on 1990 Chevrolet truck to install new front clip?
1.Start by disconnecting the battery. 2. Disconnect ground wires mounted to the fender and radiator support near the battery. 3. Disconnect horn at the right fender. 4. route this loom of wiring back through the radiator support. 5. Disconnect light wiring and air bag sensors. (airbag wiring is yellow) 6. Route all wiring back through the radiator support on the left side. 7. No other wiring needs to be disconnected. Other components need to be free of the fenders and inner fenders. They can hang while clip is replaced.
How do you install a wiring harness for a trailer hitch on a 1999 Jeep Cherokee?
You can use the factory approved method with a $125.00 wiring part. Another possibility is the $25.00 part at any auto store the wiring converter , but this may interfere with the computer system in the chreokee. It's you choise here is a link for more info http://www.wjjeeps.com/trailer.htm#WIRING
Where is a crankshaft sensor located on a 2003 Cadillac CTS?
You will find the crank sensor on the left side of the engine near the oil filter. You will have to access this from under the car. The wiring harness has to route up behind intake plenum, make sure to follow original path.
Where can you buy new engine and computer wiring harness for 1986 ranger 2.9 V6 4x4?
You cannot get a "New" engine, however you can get a remanufactured engine. They are available at most parts stores (Special order from their warehouse), or even on eBay sometimes, or you can go the expensive route and get one from a dealership. I have yet to see a "New" Wiring harness either. But replacements are easily found at any salvage yard. There are sites you can visit such as broncoii-ranger.com or therangerstation.com and people sometimes sell their extra parts of their parts cars.
What is a wire harness used for?
A wiring harness helps accelerate manufacturing and assembly of vehicles, and helps speed up repairs. Wires to support common systems are bundled together and are connected using special plugs. The easiest example of a wiring harness is on a car stereo. Almost all modern OEM car stereos (the one that comes with the car not aftermarket) only has two or three connections. One is the main wiring harness for power, speaker outputs, a signal wire to control the dimming of the display at night. This might be square or rectangle and pulled out as one plug. The "male" connection is usually on the back of the stereo, the "female" connection is the wiring harness. The second connection is the AM/FM radio antenna connection. The third connection might lead to an optional auxilary device like a CD changer, XM/Sirus Radio receiver, tape deck, DVD player, etc. etc. This would also be a wiring harness and could have a number of connections. The benefits is it makes it much easier to remove/replace components in a car, easier to route wires and cable systems through a vehicle, and makes it easier for a manufacturer to add or remove options. An example of this is from 1999 to 2003 GMT800 platform vehicles (Chevrolet Silverado, Tahoe, Suburban, Avalanche, GMC Yukon, Cadillac Escalade, EXT, etc. etc.) you can simply swap out the driver instrument panel (speedometer, tacometer, etc.) by unplugging a single wiring harness and plugging in a new one. Many owners of Chevy trucks took out the basic white/orange 85 MPH speedometer instrument cluster and replaced it in minutes with a Yukon Denali or Cadillac Escalade panel, that offered more gauges and a different style/layout. Here are some pics of wiring harnesses. http://search.live.com/images/results.aspx?q=wiring+harness&FORM=BIRE
Where is the best place to get wires through the firewall from the passenger compartment to the engine compartment in a 1994 Jeep Wrangler?
you should pass them through one of the existing rubber grommets that are already there for the wiring harness, you can also route the wires along the loom or inside the protective cover for a cleaner install.
Where can you sell the balm mushroom in Pokemon white version?
You can sell it to this chef inside a trailer on route 5.
