Dodge Stratus
SpongeBob SquarePants
Clocks and Watches

How do you set the clock on a 1998 dodge stratus?

121314

Top Answer
User Avatar
Wiki User
2005-10-16 04:52:46
2005-10-16 04:52:46

on the right side of the clock you will notice two tiny inverted pin dots, use an ink pen or something the top one is the hours and the botom one is the minutes.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Read your owner's manual. This information can be found there.

User Avatar

To replace the ignition wire set on a 1998 Dodge Stratus ES 2.5L, you must first disconnect the wires under the instrument panel. You would then hook it up in the exact same order.

User Avatar

I need to set the timing belt in my car for a Dodge Stratus 1998, that has a 2.5 motor V6.I do have the timing belt already on the car, but it not on the right setting. Please someone help me with this question about setting the timing belt.

User Avatar

All you have to do is press The hour/min button with a pen tip....easy as that

User Avatar

hahahah sorry but that's not a clock. its telling you how long your engine has been running

User Avatar

The timing marks on a '97 Dodge Stratus are located on the timing chain and the camshaft sprocket. They must be aligned to set the initial timing.

User Avatar

My 2000 Dodge Durango , my clock does not have the h or the m for setting the clock! any suggestions on how to set the clock????? Turn radio on, press set, press sel, now seek should change time.

User Avatar

You can set the clock, on your 2005 Dodge ram, by holding in the volume button. Turning the tuning knob as the volume button is held in. The time will advance with the tuning knob.

User Avatar

The clock on the radio can be set by two buttons found to the right on the display screen. H for hour and M for minute.

User Avatar

There is no such thing as a 1998 Chrysler Fifth Avenue

User Avatar

There is no such thing as a 1998 Chrysler Fifth Avenue

User Avatar

To the right of the clock there are two small buttons labeled HR & MIN. Simply push and hold them in (one at a time) with a pen or equivilent pointy object to set clock

User Avatar

The transmission computer has detected a malfunction and set a trouble code.

User Avatar

You shouldn't have to - unless your on-board computer has gone bad, but then your engine shouldn't even fire.

User Avatar

Push the set button and within 10 seconds press the seek and scan buttons.

User Avatar

The first thing you need to do is purchase an owners manual, which you will need to know the maintenance schedule. Salvage yard, dealer, Ebay, and many on-line sites are sources. Someone else may be able to tell you how to set the clock.

User Avatar

Press the set buttons for hour and minute.

User Avatar

I have set my 1998 Windstars clock by having the radio on, pushing the clock button down while using scan up and down for hours and minutes. There are likely to be a couple different clock / radio combinations - the Owners Manual for your van will have the steps for each one. See "Related Questions" below for more

User Avatar

If it is a 2.0 or 2.4 you don't ....The timing is controled by the crank and cam sensors and not adjustable....

User Avatar

There is no advance for a 1998 Dodge 5.2. You just set the distributor at the mark on TDC and the computer takes care of the rest. It is set to 0 degrees with a scan tool. It can not be done with a timing light.

User Avatar

The transmission computer has deteced a malfunction and set a code. Have the system checked for codes.

User Avatar

get the pullys lined up at the timing marks


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.