Turn the ignition key to the on position. Turn the radio off and press the set button. Set the hour and minutes using the seek buttons.
AnswerTurn the radio off first. Press the set button. Use the scan and seek buttons to set the hour and minute.
Press the set button one time. Then to set the hour you press the seek back button to adjust. For the minutes side, you would press seek forward. Then when done press Set again.
Hold down the "arrow up" button (beside the "audio" button) and it should beep, use the same button for hrs and the "arrow down" button for mins
Hold the clock button in until the display flashes the time. Then use the channel changer button to set the time. FYI: The minutes are adjusted by pushing the right side of the button, then the hour is changed by pushing on the left side. After you get to the correct time, push the clock button again.
I found this out through trial and error. Hold the "clock" button down until it starts blinking. Use the "Tune Seek Track" button up for hours, down for minutes to set the clock. Hit the "clock" button again to save the setting.
Depending on the set up. The hour/ min buttons are located on the lower right corner buttons if it is a CD player. Hold the buttons down to set the time. If you Cavalier has a set button, hold it down and while the set light is on use the seek and scan buttons to set the clock. If your 2002 Chevy Cavalier does not have a "set button" like mine, then hold down the "up/down" arrows located in the right corner for a few seconds and the time will change. down/hours up/minutes.
Push the set button and within 10 seconds press the seek and scan buttons.
hold clock button and use the seek or other button underneath while holding the clock button
You can set the clock in your 2003 Ford Escape by holding in the volume button. With the volume button held in the clock display will flash. You can then set the clock by turning the tuning knob.
Locate the odometer reset button. Turn it to the left and hold to set the hours and turn it to the right to set the minutes.
How do youchange the clock on a 2002 zx2 ford escort?
To set the clock on an Emerson microwave oven, tap the clock button and then hit the numbers according to what the current time is. Then tap the clock button again. If the numbers go back to 000, then there is a malfunction with the clock on the microwave.
How do you set the clock on a 2000 s-type jaguar?
'how do I set the clock on a 2001 mercury mountaineer'
Press and hold the " CLK " button To adjust the hours use the " SEEK " button To adjust the minutes use the " TUNE or TUNE DISC " button
If by the clock you are talking about the one on the radio it is very simple. 1st> press and hold in the clock button for about 5 seconds 2nd> while still holding in the clock button press the SEEK button for the hours and the SEARCH button for the minutes. 3rd> release the clock button and you are all set
There is a Up and Down Arrows becide the audio button, Press the arrows for about 3 seconds it will beep, It will change the Hour and Min.
You can set the clock on the Chevrolet S 10 pickup truck radio by holding in the power button and advancing the clock with the tuning button. The tuning button will move the clock setting forward or backwards.
Not to be smart but there is a little button on the face that says "clock".
To set the clock in your suzuki aerio, you have to put both the ill button and the degree button while another person pushes the min button and the hour button, trust me a pain in the rump.
The 2005 Jeep Liberty clock can be set by holding in the volume button. With the volume button held in the clock will flash. While the clock is flashing turn the tuning knob to adjust the time.
Press the set button then within 10 seconds press the seek and scan buttons to change the time.
To set the clock on your 1994 Cadillac DeVille, turn the ignition on with your key. On the bottom right corner of the clock you'll find the 'set' button. Press the button and immediately press and hold the 'seek' button. When the clock gets to the hour you want, release the 'seek' button. Next, press the 'set' button again and press the 'scan' button, and hold it while it scrolls through the minutes. When it displays the correct minutes, release the 'scan' button.
assuming this is the digital clock, you hit the clock button on the dash, followed by the reset button followed by the clock button. at this point, you should be able to hit the clock button to advance numbers, and the reset button to change the numbers you are setting. if its the analog clock, pull on the knob and turn it