ford festiva stopped while driving it has fuel and power it just
wont turn over
how do you set the timing belt on a 1997 ford contour 2.0 4cy
May be controlled by computer and non-adjustable
There is no provision for setting the ignition timing. The timing is set by the computer by way of engine sensors sending signals to it by such things as temperature, load, speed, and intake air.
where to set timing for a 1988 ford ranger 2.2l
how do you set or check the timing on a 99 ford expedition?
Im replacing the timing belt on a 1995 Ford Escort 1.9L. How do I Set the timing on it?
How do you set the timing on an 1988 ford ranger 4 cylinder
"How to set timing on 1991 ford escort lx 1.9?"
how do I set the timing on a ford f700 truck 370-4
how i can set 1997 Mitsubishi diamante timing belt Answer how i can set 1997 Mitsubishi diamante timing belt
mk3 fiestas dont have a timing belt it is done by a chain tis chain will probably outlast the engine however if the timing is lost the chain is lose and is a big job to change it best looking for new engine it will be easier to change engines wja
how to set timing on ford 1987 f-100 302 without timing light
How to set timing in step by step
how do you set the timing on a 1.25 ford fiesta zetec s engine ?
What is the timing for a 1998 ford ranger 2.5l
The timing can not be set manually it has to be set by the dealership through the computer.
Ignition timing is automatically set. sorry.
Modern vehicles have their timing set by the PCM (computer), there is no adjustment.
trying to set base timing on a 97 Chevy c1500 with a 5.7 engine the wire to disconnect to set base timing is ?
how do i set the timing on a 1995 ford escort LX??
you cant set "timing" you have to have a scanner to set cam sensor to 0 +or-2
you dont its preset by the timing belt
You can set the timing on a Mitsubishi mirage 1997 going to the setting and finding the setting properties. The setup should be the second on the listing.
The timing on a 1997 Dodge Ram is not set with a timing light. The distributor rotor is lined up with the mark on the pick up plate when the engine is at tdc to set base timing. The timing is then fine tuned with a scan tool. The scan tool is used to set it exactly to 0 degrees.
The timing is computer controled and not setable.
how to set the timing on 1978 f100 ford 400 engine
denomanater scanner can program your timing
You need a timing tool
How do you set the timing on a 2300 mustang
Timing is done by the PCM. No manual timing can be done with out a new PCM
where are timing marks on 89 ford probe 4 cylinder I have the bottom not the top
The timing is set with the aid of a scan tool. It can not be done with a timing light. The timing is set with the aid of a scan tool. It can not be done with a timing light.
how do you set the timing for a 1997 Chevy 350 5.7 engine
timing should be set at 10 degrees BTDC. be sure you unplug the spout connector before you adjust the timing.
u need a scanner to set it
how do I set the timing on 2001 ford escape xlt 4 cylinder
The timing marks for a 2002 Ford Explorer are located on the timing chain and cam shaft sprocket. They must be aligned with each other to set the initial timing.
There are no timing marks. The timing is controlled by the PCM. Power control module. It is not possible to set the timing with a timing gun.
the timing should be set top dead center with the number one spark plug
What are timing marks for 97 tacoma 2.4
That requires a OBDII engine scanner. You CANNOT use a timing light
To set the ignition timing on a Ford Probe GT 95 with an MX engine, remove the two 12 mm head bolts holding the distributor in place. Then rotate the distributor to set the ignition timing.
Timing is computer controlled.
This is set electronically by the computer...nothing to set. Answer the only wayto look at the timing is to set up a timing light and look at the crankshaft pully. but there is no way to set it on this truck
In mechanics books it says to set the timing to 6 DBTDC with a timing light, (Caution: this is with all the pollution stuff on the motor) If you removed the pollution gadgets the timing should be set with a vacuum gauge and the timing will be 12 DBTDC.
You do not, It is not adjustable. It is controled by the computor.
i think you just take it in
you can't,it's controlled by the computer.
Timing is pre-set by the PCM
It's controlled by the computer.